I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
I have a nrf9160 DK but when upload SLM application to it i can not send AT commands to it over it's usb port but in asset tracker application it works i want to modify SLM...
Could someone offer some guidance in how it is possible to keep the radio within IDLE mode between transmissions when operating in ESB mode? I have a sequence of transmissions...
Hi
I'm doing some S/W based on nRF51822_xxAC. I want to split RAM into 2 regions, as following:
+-------------+ 0x20008000
|__ __ _ __ |
|APP ZONE2 |
+-------...
hello, I'm trying to read the status register but all I am receiving is 1111 1111, I tried to change the code to read RX_ADDR_P0, but I also receive 1111 1111. can you tell...
It suggests that it holds the permission regarding whether a chara. can be read, but isn't that kinda redundant since there are tons of other similar properties out there...
Hello
Can i program an nRF52 chip using nRF51 DK. I plan to take advantage of the features of nRF52 including higher memory, storage and the NFC
Thanks
Hi,
My company has been running into an issue with the NRF51822 where the MCU appears to enter debug mode unexpectedly and I wanted to see if any others had experienced...
I successfully used my nrf52DK with latest production SD 132 and latest SDK (12.2.0), everything is on latest Keil v5. Then I needed to program another board (nRF51 Dongle...
Hi Nordic Tech support team，
I have some problems with nrf51822 OTA.
My Bootloader is single bank Bootloader。When I update nrf51822 firmware by OTA with android apk, I found...
Hi i'm very frustated with myself not the modules , i could make a pair of them to work perfectly in a pic 16F886 , now due to other project i have to use a dspic33fj64mc202...
We made a version of bootloader_secure for our own purposes. The problem is now that application must be uploaded twice into the device (nRF52) before it really gets updated...
Hi,
I am working on bootloader_secure example on SDK_12.1.0 and set APP_ADV_TIMEOUT_IN_SECONDS to 180 to stop the advertising after 3 mins.
All looks fine and device...
In tihs video , and others this guy has done, the transmission speed of the nRF24L01 2.4G module only achieves a speed of, at best, about 300 packets per second (where a packet...
We are using nrf51822ab, s130, pca10028. After dumping the soft device the free space left is 20kB, my code size is 48kB. I am able to dump the code into device but its not...
I am following ble_peripheral example of nrf51822 SDK 8.0. I have found ble_gatts_char_md_t , ble_gatts_attr_md_t and ble_gatts_attr_t confusing. I want to know the difference...
