Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hello, I read in the documentation how to create a model, in the client model, which defines a struct: simple_on_off_msg_set_t {uint8_t on_off, uint8_t tid}. I do not understand...
See: http://www.keil.com/forum/63929/
Everything here refers to J-Link, eg devzone.nordicsemi.com/.../a-working-demo-of-monitor-mode-debug-mmd-on-sdk-15-please
and Google...
Hello,
I am wondering that what exactly are the differences between libmbedcrypto.a and libmbedcrypto-software.a?
I read through the SDK documentation about the opethread...
In SDK 15.2 in ble_gap.h
#define BLE_GAP_SCAN_WINDOW_MAX 0xFFFF /**< Maximum Scan window in 625 us units, i.e. 40,959.375 s. */
#define BLE_GAP_SCAN_INTERVAL_MAX 0xFFFF...
Hi Everyone,
I'm using nrfutil in an arm cortex a8 running Debian 9 with kernel 4.14.49. The processor is connected to a NRF52 dongle through USB. I'm trying to flash (using...
Hello ! My custom board is working fine (with the last programm I flashed into), but I can't access it with my debugger and I can't flash it again. When I try to flash it...
This is my Output, Looks good but not working/
Preparing target for download Executing script TargetInterface.resetAndStop() Reset: Halt core after reset via DEMCR.VC_CORERESET...
I am using nrf52832 with latest version of s140 softdevice.
I migrated a project, that was used on a nrf51 chip, to the latest sdk version.
The problem is that the measured...
The zipped project attached to this blog doesn't say what SDK version it should work with - but it certainly doesn't work with v15.
https://devzone.nordicsemi.com/b/blog...
Good afternoon,
I have a question regarding the ble_app_hrs_rscs_relay example. I am using this example to read scan response data from a peripheral without pairing with...
Hello, I am useing nRF52832 with custom-made board.
SD 5.0.0 and 14.0 SDK
I have a strange issue - i am using custom-made service to transfer data from/to smartphone...
I am doing an application that relies on continuous scanning of the beacons. So if I use SCAN_RSP in the advertising device, would this affect the timing of the scanning device...
I want to use BLE 5 for authentication using NFC nrf52840 on raspbian os i.e radpbery pi 3 compatibility. Could you please help me to know how this should work.is there any...
Hello, I want to establish wireless connection between PC (windows) and nRF51DK board. I want to send data from the sensor connected to DK every 200ms to the PC.
My question...
