I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I'm using nRF52 DK, mesh SDK version 2.2.0
I want give demo of the Light-Switch example application by forming network through mobile. I found that through mobile application...
We recently purchased the nRF6700 and nRF24LE1-F16Q24-DK from Mouser Australia. The Getting Started Guide is completely misleading (totally out of date). e.g. No product keys...
Hi guys,
I just wished to quickly clarify the ordering of notification/indication behaviour on SoftDevice S132/140.
If I were to post a notification then immediately...
Hi,
I was trying to get SAADC readings from AIN0 to AIN7 and also from VDD but I'm getting strange results. There is nothing connected to the pins but the measured value...
Recently I have encountered a software hanging issue on one of our products. It was based on nRF52840, with FreeRTOS (Thread SDK v1.0). The issue was apparently related to...
My application needs to keep time and support local time as well. I have implemented a service that allows setting the epoch seconds as well as a local timezone string. With...
Hello, I have an issue with the init packet on SDK13.1. i used nrfutil to generate the .dat and .bin files that i read with Hex editor to transform then into byte arrays....
We've purchased the nRF6700 (nRFGO Starter Kit) and nRF24LE1-F16Q24-DK (Dev Kit) from Mouser Australia.
Both products arrived without Product Keys - so can't download any...
Hi all,
I am using the S332 softdevice for dual ANT/BLE stack in SDK v14.2 bundled with bootloader_secure_ble, which was apparently power optimized in SDK v15.0.0 (see my...
I have made a custom board based on the raytac NRF52840 module (MDBT50). When i load in the USBD CDC example (SDK version: 15.2), The device is not detected. There is no output...
Hi, I would like to build a mesh network with ANT so I tested the ANT scan and Forward example for nRF52832. And the current consumption is around 5mA, is this current normal...
As in the title, I installed 64bit nRFgostudio, however it crashes just after opening with the log below. It opens fine when I do not have my Thunderbolt 3 docking station...
Hi,
How can I send message from servers other than 0x105 and 0x106 to client?
I receive status message in client from servers 0x105 and 0x106.
I can send message to...
I'm trying to use the SDK 15.0 saadc example with a potentiometer on AIN0, and I'm getting weird values. Left pot pin connected to VDD, right pot pin to GND, center pin to...
Hi Nordic:
I want to add some rtt log in the bootloader code, so I make bootloader flash start at 0x77000, size is 0x7000, and my application's FLASH_PH_SIZE is 0x77000...
