HI,
I am using the nrf_desktop sample in NCS V3.0.2, I want to buil with prj_release_dongle.conf , the setting
but build fail, I check the file Path: it should be F...
Hi:
I'm doing exercise 1 of lesson 1 of the nRF Connect SDK Intermediate course. It says: Get the source code of this course as a third-party repository within the SDK itself...
I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
having issue with nrf51822
nrf51822 breakup board was running fine with S130 2.0 stack and ble_app_uart
Now facing issue such that when softdevice enabled is called the...
Hi,
I just switch to Embbeded Studio following the last tutorial ( here ).
I'm working on NRF51822 with SDK12 and TWI_sensor example (without SoftDevice). I followed...
I see from the release notes of s132 4.0.0-2.alpha that it adds:
Support for 20 links in total with freely selectable role (Central/Peripheral) for each link.
I want...
Hey,
I am trying to control an external LED using two nRF52832 boards. I am using "nRF5_SDK_13.0.0_04a0bfd\examples\ble_peripheral\experimental_ble_app_blinky" code for...
I'm trying to use the BLE sniffer in a quite busy BLE environment. Unfortunately, it always crashes after a few seconds.
I'm using:
ble-sniffer_win_1.0.1
nRF51 Dongle...
Hi,
i am using PCA10040 DK board,
working on ble_app_Uart example, i have created one timer(app_timer) here is the code:
printf("init\r\n");
ret_code_t err_code;...
Dear all,
My chip is nrf52832, and sdk version is SDK12.1.0_0d232a. And tried to use ble service and spi master function.
I create a timer to send spi command every...
hello all:
my mcu is nrf51822(QFAA), and use it to make a blue device ,i want to use mcu's reset pin to reset it, just use hardware. i add a key to connect the reset pin...
Hi,
I have searched for examples which will use passkey to connect with android, but didnt find any.
I want ble_app_hrs example to connect with nRFConnect in android by...
HI，i develop my project base on “examples\ble_peripheral\ble_app_uart” and “nRF UART v2.0”。i hava large data transmit from phone（androd） to nrf52832。
but when send a package...
I need to save some data on the flash storage. This data will be some structures and I will write, read and modify them as and when required. I am also using peer manager...
Hello
I came across interesting problem I couldn't find answer to.
In my project bss size printed by arm-none-eabi-size is larger than the value that can be calculated...
I'm testing with ANCS example(SDK11.0.0), PCA10028 and Iphone, observing packet with sniffer.
at the first connection,
master sent EDIV( 0x0 ), Rand( 0x0 ), SKDm and...
