Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
Hi,
I'm not sure whether it is right place or not to discuss this.
We are planing to use nrf52840 in our new IOT project. We required nearly 30 development boards and...
I don't want my consumer to do provisioning of mesh-DEVICEs one by one (using Android or iOS APP) since in such case if he has 50 mesh-Devices in that case he will get frustrated...
Hi everyone,
It looks like there is a bug in GZP host example.There is a function gzp_host_chip_id_read where flash is accessed at GZP_PARAMS_STORAGE_ADR. But there is...
I am using the following to extract the Device_Name from an advertised packet received on an Arduino Primo:
peer.getFieldInAdvPck(BLE_GAP_AD_TYPE_COMPLETE_LOCAL_NAME, advertisedName...
Hi!
I have a question about the Mesh SDK. Is it currently possible to get the physical source of a relayed message (thus the relay that send it) out of it? I only seem...
I use buttonless_dfu_app as template. SDK 14.2
Q1. Could someone help me.. After I updated my app I have changed crc (if more than just few changes), so bootloader installed...
I made all steps in a guide
devzone.nordicsemi.com/.../
All works fine. After that prepare my own firmware like appendix 1. Also works good. I merge
bootloader_setting...
Hello,
i'm trying to run the ble_uart_example on my nRF52840 eval-board, but it always fails on this line:
err_code = ble_advertising_init(&m_advertising, &init);
APP_ERROR_CHECK...
Hi, everyone,
I develope the project with BLE support. In my project I need to define the time server. For this purpose I tried to find any example reffered to it, but no...
It is a sensing-processing-actuation based application. Just want to use the nRF52832 module for BLE communication( a part of the application).
Is there a direct API in the...
Hello,
I have an application where an nRF52832 peripheral (S132 v3.1.0) transmits a 5-to-10 MB file to an nRF52832 central (S132 v4.0.5). The peripheral sends the file...
Hello,
I have bought an nRF51 dongle with a SEGGER J-Link.
I have downloaded all the SDK and everything from nordic website.
If i open an ble peripheral example in uvision5...
Hello i cannot get uart to work correctly on these pins. The board seems to reset when i try to run uart on these pins. I can get them to work on pins P0.06 and P0.08. I think...
