Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
Hi.
I wonder if you could help me:
I'm using a thingy91x and would like to work with the npm1300. In the case of this hardware, the PMIC npm1300's i2c bus is connected...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
I have a strange problem with pstorage function with nrf51822 with s110 v6.
I need to use nrf_delay ( about 1 second long ) after store and before read.
This is the source...
Hi,
I am using softdevice 6.0.0 and ble_app_hrs example in keil on a custom nRF51822 board. Compilation goes fine but when I try to debug I notice that the firmware seems...
Hello,when i get connected to the phone,when i call err_code = ble_hts_measurement_send(&m_hts, &simulated_meas) and err_code = ble_bas_battery_level_update(&m_bas, battery_level...
Hi
I am using S110 v6.0.0
I have written an app that has a single service and I then register the same characteristics until it fails. The properties is 0xA (read/write...
Hi,
The nRFgo Studio v1.16.1 will up side down the contents of old profile XML that created by v1.16.0 or v1.15.x.
And use the new generated services.c and services...
Hi,
So I'm using a BT 4.0 dongle (Laird BT820) to set up a LE notification loop with the nrf8001 (RedBearLab shield on Arduino) using gatttool on Ubuntu 12.04. This works...
I've used the nRF8001 on several projects with good success, so I'm generally familiar with the chip's operation. But I'm seeing an issue on a new (custom) board that I'm...
We are currently researching which BLE chip vendor to use so this question is directed at Nordic personnel familiar with the S110 stack's capabilities.
In a situation where...
I would like to use the nRF51822 evaluation kit as an observer to detect beacons and take action based up the RSSI value. I can't seem to find any source code for S120 or...
I got the Dynastream N5 kit and have successfully used it with limited ANT work and was trying to get BLE working but can't get a driver for the USB dongle. On the 51422 product...
Hi,
Repro, using the Nordic hid-profile + iOS 7.1.1:
Pair the nrf51822 based hid device via the iOS bluetooth menu.
Turn off nrf-device.
Boot up the nrf-device...
I want use pstorage write and erase flash,as shown below:
//pstorage_init(); // device_manager_init have been called,so there's no need to call
err_code = pstorage_register...
I currently have a design that has four characteristics (all strings) in a custom service. Each is less than 20 bytes and I send them out one at a time. i.e. one characteristic...
Hi All,
I am working in the sleep mode with system off and wake up with internal RC clock.
It function well when connected to EV board...
I see the "Emulated System...
