It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
Hi.
I wonder if you could help me:
I'm using a thingy91x and would like to work with the npm1300. In the case of this hardware, the PMIC npm1300's i2c bus is connected...
RTT log output issue
Hello, I am using SDK v3.0.2 and toolchain v3.0.2. After building and flashing my firmware, no logs are being output to RTT Viewer. What should I do...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Hi,
I have ordered nrf51822 development kit with one of my local vendor. when the product came to india , it was checked in customs office somehow the samples in the kit...
I'm using an nRF51822. Currently, I'm using the low power sleep mode. The device uses about 1.5 uA in sleep, which is great. The firmware wakes up the device every n minutes...
I have a fully functional code for 8-bit data acquisition using nrf24le1. Now i want to upgrade it to 12-bit resolution ,but i have problems in doing so .
In my project...
I am making a module using nrf51822 and a chip antenna.
I need a layout from nrf51822 to a chip antenna through matching chircuit.
Unfortunately, I don't know how to...
Hi,
1. I want to design a product as a tag,which can read the temperature and transmit the data to a host,the host can read several devices' data. which mode would I use...
Hi everyone,
Just recently I've got two nRF6310 EVB boards with a nRF51822!
When I connect board via USB and open the nRFgo Studio, it can recognize the board as nRF ISP...
For nRF5122 BLEStack, it is analyzed that the event is processed in each of the interrupt handler for the interrupt terminal BLE
I understand that is processed through the...
I tried to set a GATT server and a GATT client for each Central and Peripheral, but code exceeds the memory limit.
Then i consider to transport by HCI. But I totally confused...
We have code that must erase a page in flash every once in a while, while S110 is advertising. The advertising interval is set to 0xF4 (which is about 150ms) and we have scan...
I am using nrf51_sdk_v6_0_0_43681 and s110_nrf51822_7.0.01 wiht nrf51822, and I modifiy code based on ble_app_uart.
Here I am trying to launch a continous ADC sample with...
Hi,
whenever i try to program the PCA10000 ( USB dongle) using MASTER CONTROL PANEL(3.4.0) i'm getting log messages like as below,
"...........
Successful flash!
Enabling...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm following nAN-29 and when I go to import the Eclipse project file for ble_app_hrs I get a message "No projects are found to import". I've pretty much followed nAN-29 to...
I've been working on an interrupt driven I2C driver. I have the basic driver working, but I'm hoping to squeeze a bit more speed out of it.
I'm mostly doing fairly long...
This is an howto on restoring your nRFgo motherboard firmware.
Error code can be similar to this from nRFgo Studio:
Starting bootloader on board 0
Could not start the...
