Hi,
I want to add scheduler server to the mesh/light sample with nrf52DK, I change the element define like below:
static struct bt_mesh_elem elements [] = {
BT_MESH_ELEM...
Hi,
I’m working with an nRF52832 DK board that’s stuck in bootloader mode—LED 5 just keeps blinking. Here’s what we’ve tried so far:
Held the IF BOOT/RESET button...
Hello,
After I upload a new signed image to my device using MCUboot serial recovery (single image), MCUmgr Img_mgmt_client API
img_mgmt_client_state_read() always fails...
Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
We are using nrf52840 USB dongle to get PIR sensor readings and send measurements over the Bluetooth Mesh Schematics are following: We increased power for peripherals to 3...
Hi:
When I use nRF51822's 2.4G Radio(not BLE),I want to improve anti-interference level,Make sure that all my pairs of host and device can communicate normally.
Thank...
Hi
Looking at the AGPS sample code, it seems GPS/LTE is turned on and off using AT commands (AT+CFUN=x, x in {20, 21, 31}).
Do you recommend NOT using PSM when using AGPS...
Hello,
I have several nrf52 Development Kits which will be used for creating a Bluetooth mesh network. They sport the NRF52832 SoC.
Do they have, or will ever have, support...
Hello
*Environment
- LG V30 (Android 9)
- nRF52832, 15.3.0 SDK, S132
- nRF5340 ( I can't find SDK version)
I have some issue.
LG V30 Mobile can't reconnect...
Hi,
I am using nRF52840 USB dongle and DFU trigger library to update firmware without push any button.
The Python 2.7.x is working fine for DFU trigger into the DFU mode...
Hi!
I am developing a iot solution and I wanna send sensors data to broker by MQTT publisher. In my code already has the W5100 development and now I want to connect my device...
Hello,
I would like to create a new box in the nRF cloud for recording additional data. I know these boxes allow exporting the recorded data into a CSV file, which is ultimately...
Hi,
I have the below queries regarding the power consumption and memory
1) If my device is connected to the mobile phone and if it is scanning and the same it is advertising...
I'm trying to develop a code for the nrf52840 with a BLE link as Peripheral and Server (common configuration, but no SDK example). I start with a GATT server and changing...
Hi,
I try to use nrf51 dougle as a sniffer.
My nrf51 dongle not show up when connected to PC, when press the reset button, it only shows the boot-loader.
I try to find...
Hi everyone,
I want to measure the strength signal of BLE of my device. I need to do this measure without connecting/paring my device to any other, just during advertising...
Hello, Are there plans to include the nRF52833 reference design to the Eagle library on github ? In particular nRF52833 QDAA QFN40 (with the 201's).
There was a similar...
Hello,
I'm using the nrf52840 and SDKv16 to interface with an SD card. An SD card block is 512 bytes. I would like to do this:
1. Get the card ready for a write (use blocking...
