HI,
I am using the nrf_desktop sample in NCS V3.0.2, I want to buil with prj_release_dongle.conf , the setting
but build fail, I check the file Path: it should be F...
Hi:
PLEASE CANCEL THIS TICKET
I'm doing exercise 1 of lesson 1 of the nRF Connect SDK Intermediate course. It says: Get the source code of this course as a third-party...
I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi All,
Can one safely assume when sending a packet to a destination address using the ping command in the CLI, that the payload echoed back is the payload transmitted...
mainc.txt
we can use INTENSET to enable certain events on the radio as in line 460 in mainc file attached. But how to enable this on the radio as a whole.
I basically...
Hi Nordic,
I am trying to enable the DC/DC converter on a QFAAH10 (revision 3) .
I am using the s130 v2.0.1 SD .
----------
1. sd_power_dcdc_mode_set(NRF_POWER_DCDC_ENABLE...
Hi,
If I configure the radio notification to ACTIVE and then set a DISTANCE of 800us, is there any way that I can configure PPI to toggle a pin for example?
I know that...
We are applying the CE certifcate for a product using nRF51822 and softdevice S130. Certification lab requires us to fill in below techanical questions. Please help to answer...
Hello, my program stuck at these assembly codes:
I decided that it was stuck because I keep pressing F11 and it just go around in circles in these 4 lines.
So:
...
Can't I connect to device that hasn't been discovered yet??
I'm trying to connect one device( A ) to another device( B ) which ADDRESS is known but never discovered yet...
Hi there,
We're looking at doing something with beacons so that we can make use of the way iOS handles scans for them in the background differently to other peripherals...
The debugger does not work with the latest GNU toolchain for ARM Cortex-M build. It throws the following error on Eclipse:
Could not determine GDB version after sending...
GPIOTE Library makes my Board(nRF51422-QFAC) Brick??
I just build my nRF51422 Board, and It's pretty working well before I've used GPIOTE Library.
Before using GPIOTE...
Hi everyone,
I am seeing an issue where the SPI (master) ignores the first byte of RX buff and begins storing the received bytes from RxBuff[1] instead of RxBuff[0]. In...
Does anyone know if there is any documentation of nrf51822's current consumption? Perhaps, something similar to CC254x's Application Note . I'm mostly interested in the current...
Hello,
I would like to build two boards that can send small messages between them, at long distance. For that I would like to use some of your devices (I used 51822 in...
Hi
I have working module which communicates via uart with another module. It works good, unless it is heated to 40C. After that temperature UART communication is not correct...
