Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
I check the function spec that we can use use 32kHz RC as LFCLK, so I have no external 32k crystal connected with XL1/XL2 on my board.
I have set
NRF_CLOCK->LFCLKSRC =...
Hi,all:
I have a question.
could I use android/ios APP to connect several BLE devices at the same time?
because I want to use andriod APP to control all of the BLE...
I'm trying to write a central BLE with the dongle(PCA1000) using s120.
I programmed s120 sd ver 1.0 the same way as the s110 with the nrFGO ver 1.17.
However i keep getting...
Hi all,
I need to change the device name frequently to show button status.
So remote device can see button status without connecting to device.
Is there any way to...
Hi guys,
i have a service with more characteristics and more states. Not every characteristic should be available in each state. Thus there are services which are just...
Using the S120 soft-device in the Central role, there does not appear to be an
example or documentation describing how to scan for a 128 bit UUID service.
Has anyone tried...
Apparently there is some limitation on length of the paths with Keil. The paths are specified under "Options for Target" --> C/C++ --> "Include Paths". Due to this limitation...
I downloaded the nrfgo Sdk for the nrf24lu and nrf24le. In the projects folder there are several examples, two of which are of interest. The first is entitled "bootloader_32K...
Hi
I'm having a strange behaviour when using the TWI HW peripheral for reading from an I2C device. My application tries to read one byte from a register in a I2C device...
Hi,
I'm done with the hardware interface of my current project.
Right now I have a service running with a custom UUID, by writting this characterisitics you have access...
Hi,
I'm having the purpose to use nRF51422 /ANT to connect a relatively data hungry ANT device. The nRf51422 specs expose three programmatically available data rates : 250...
Hi,
I've written a nRF51 SWD-JTAG programmer.
I want to enable it to check for minimum softdevice version and error out if a too-old softdevice is found.
It is easy...
I want to communicate four same devices with different hosts. i know that one host can communicate to seven devices and also a device is able to speak different hosts . i...
Thanks for the response. As a test, I loaded the same code onto a PCA10004 and it seems to work as you described. A breakpoint at 217 does get triggered when it receives data...
