Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi All,
I have just started working on interfacing SD card with nrf52 using SDK 12.0. I have to write to SD card at a rate of 84 packets per second and each packet consists...
Hi
I am checking out NRF51822, NRF24LU and NRF24LE1.
Below are my design requirements:
Smaller the size, the better. 7x7mm is OK. prefer smaller.
Lower power...
Hi, Nordic
I have 3 nRF52 devicies, one as Gzll Host, two as Gzll Device.
they use Gzp to pair, when paired, two Gzll Device send payload via different pipe ( 2, 3)...
Hey everyone, I'm trying to use lmt70 with nrf51822. So, first of all, nrf51 has 10-bits ADC, the data sheet of lmt70 is recommended 12-bits of ADC.
I plugged the sensor...
I use nRF51822 (Multiprotocol Bluetooth low energy/2.4 GHz RF System on Chip).To transmit informations with smartphone.
I have to set up a self-certification application...
Dear Nordic.
Is NRF_POWER->GPREGRET register writing in NVMC?
FICR and UICR is saved in flash memory(NVMC) as written by [nRF51_RM_v3.0.pdf].
But, GPREGRET register...
Hi，
I have the following setup
Chip: nrf51822 chip
SoftDevice: S110
Firmware: dtm exmaple.
I use device test Bluetooth certification in korea(RF output from our...
Hi,
I'm new to development using nordic's products. Basically I'm a Hobbyist working on a project of mine, which needs a low cost wireless.
I was looking for a Rf Soc and...
Hi, has anyone used the nrfgo SDK (for the nRF24LE1) with either eclipse or SDCC? We use those platforms already, so it would be great if we could add your SDK to our toolchain...
Hello,
I have been using the nRF52832 DK with the GCC + Eclipse setup and running both example programs and my own. Everything was functioning properly and I was ready...
Hello all,
I try to initialize the uart module inside a c++ code as follow:
#include "uart.hpp"
void Uart::uart_init()
{
uint32_t err_code;
app_uart_comm_params_t...
I am not sure how exactly the NRF52 handles a call to start a new sequence. There are 3 different scenarios (trying to start a new sequence before, right after and way after...
Hi,
Here I have a code for HC-SR04 from electronut.in which has been written for softdevice 110,
right now I am using BDM-200-EVAL-M and SDK version of 11 which supports...
I use the IAR 7.5 compiler and SDK 11.0.0
The program does not work well so I modified the starting address of rom(0x1c000->0x0).
(Ble_stack_init) After part does not work...
