Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
RTT log output issue
Hello, I am using SDK v3.0.2 and toolchain v3.0.2. After building and flashing my firmware, no logs are being output to RTT Viewer. What should I do...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
good time dear Engineers!
faced with a problem of S132 nRF52. ADV data of packet lost.
I compared the RAW data according to screens below:
If I use nRF Connect ...
Hi, Nordic
I see this question: devzone.nordicsemi.com/.../ , I follow it, then I can see log in J-link RTT viewer.
But when it work, I find after some time, the old log...
Hi would like to evaluate the consumption of my pcb in connected mode using a nRF51. For that I use the nordic excel tool : "APM_nRF51822_S110_v3 0c.xlsx".
But I really don...
Hi,
I am trying to save some data in flash by using the Flash data storage.
However, everytime I try to write data to the flash, the module returns this error code:
FDS_ERR_UNALIGNED_ADDR...
Hello,
I'm making bootloader(nrf51822xxAA SDK12.1.0 and SD130 version).
I have some problem in micro-ecc installation.
To install micro-ecc, complete the following...
Hi, I have a problem with DFU OTA.
I use nRF Toolbox's DFU to upload nrf51822 QFAC, most times it works.
However several times, after the app altered "** bytes transferred...
Hi,
I want to generate a 2.048MHz clock on one of the IOs of nRF52832. Could you comment on following questions?
1- Can I generate this frequency (with no load on CPU...
Hello, I work with some ADC 24-bit (HX711) and for getting data from that I need after low level on first gpio pin to fed 26 pulses to that with time period about 1us on second...
Hi,
I am using ble_app_uart_c_S120
How can i support more then 1 bonded connection?
i try:
#define DEVICE_MANAGER_MAX_CONNECTIONS 7
#define DEVICE_MANAGER_MAX_BONDS...
What's the correct settings for nRF51822 CEAAE0 (0x0079) with dfu example in SDK v11 ?
I believe the chip I am using is a 16KB ram 256KB rom version, but not sure 51422 or...
reco_scan_req.PNG
Now i am doing a test of RECO beacon which use a nordic chipset, nrf51822.
But something strange came up to me during the test with Ellisys bluetooth...
Hello,
I know that this question has been asked in the past but I could not find any recent post about this topic, and there have been many updates to the SDK since the...
I am using NRF52DK and SDK 12.1. I am using BLE. I currently am not using Peer Manager but probably will be implementing that in the future (of sooner if that makes my question...
