Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
Hi.
I wonder if you could help me:
I'm using a thingy91x and would like to work with the npm1300. In the case of this hardware, the PMIC npm1300's i2c bus is connected...
Hi,I'am try to update the bootloader. But it stop at 1%. I don't what I miss.
james_boot.hex
james_bootloader.zip
Log 2016-09-06 11_36_54.txt
Dfu_bootloader_via_hex...
hello,
I'm using S132/nRF52/SDK11.
I start a firmware development based on Nordic UART example, I kept the BLE NUS part (I loop back the data received over BLE) and...
Hi All,
Just noticed SDK12 was released last week, with build in support for S132, v 3.0.0. Judging from the compatibility matrix and notes, it looks like it removed support...
Hello,
I'm trying to set a new environment with the SDK12 that'll be less cringy than the one I was running under the previous one.
Basically, what I want is a workspace...
Hi
Using an nRF52832 and SDK11, I have the following issue:
I want to use button 0 with a regular push for functionality and a long press to go to sleep. The detection...
Hi, I'm trying to move from nRF5_SDK_11.0.0_89a8197 to nRF5_SDK_12.0.0_12f24da and faced an issue. I have build error in
....../nRF5_SDK_12.0.0_12f24da/components/libraries...
Hi@all,
i'm trying to connect to a BTLE Printer (printer -> peripheral) from my central (nrf51822 board). But i cannot use the standard discovery examples because i cannot...
Hello, I have pca10001 board and I would like to read an analog input from ADC.
Is there any complete example which I can test using potentiometer ?
Thanks
I'm trying to write some data to flash memory (32 bytes) every 1 minute. the data are not NULL but then I noticed that sometimes (not always) the pstroage module write zeros...
Hi,
I am programming and debugging an external customised board by following the DK manual and the below link:
electronut.in/.../
I use the interface P20 instead of...
Dear all
I want to add the static pin to my project(s110 stackV8.0, based on SDK10), add the follow code to gap_params_init:
uint8_t passkey[] = STATIC_PASSKEY;
m_static_pin_option...
Dear all
Good day!
I want to develop the Android APP to received the BLE's ad raw data(which is dynamic change). Which API should I called to get the raw data? And should...
Hi,
I am using nrf51822xxaa , Keil Uvision 5.14.2.1. SDK 10.0.0 and S130. I need optimisation level O3 for most parts of the code, except for one part (about 10 lines of...
