Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
Hello,
I am new to BLE shield and arduino stuff. I am working on a project where I have to send the sensor data i.e. temperature sensor, humidity sensor and pressure sensor...
Hi,
I'm using the nRF51822 and pCA10001 as SPI slave.
For reasons beyond my control I have to read the Rx Buffer before the CSN is released.
Yes, I know I shouldn´t do...
Hi!
Could I find somewhere (I was trying in Nordic docs and in previous posts but everything refers to previous versions of softdevice) how to perform bonding with key...
Hello,
When designing a 4 layer board with the nRF51822, should I connect the chip and impedance matching circuit to analog ground and keep the other digital chips isolated...
use nRF51822_Evaluation_Kit
I want to auto bonding by peripheral ,once peripheral connected with center(android app).
Is there have any API to send pairing request?
Hi, I tried uploading the example code from \nrf6310\spi_master_example to nRF51822 evaluation kit board, but no matter what I do, I always get SPI error. Not compile or upload...
Hi,
is there a nRF Master Control Panel equivalent App for iphone?
I'd need an app where I can set custom characteristic. The background is to update the device using...
I'm a begginer in embedded program. I have a mbed HRM 1017 that
is pin-compatible with Nordic PCA10004. .
I'd like to make a simple app to print out "Hello World" to terminal...
Hi guys,
How to update softdevice on mBED nRF51882 kit?
Details:
I have couple mbed dev kits with nrf51882.
I use Keil for development but will move to GCC after while...
Hello all,
I wanted to ask if there are any cad files for Eagle or other hobbyist level design tools for the nRF51 chips before I spend time to create and debug them? ...
hi guys,
I'm pretty new to nordic ble development, but I have a fair idea of the differences between EK, DK and the mbed enabled MKIT.
I'm trying to build a deploy about...
I have been following this post and pure-gcc to set up my eclipse environment in ubuntu 14.04. Thus far everything works well except i cant figure out why the softdevice is...
Hi,
I made own board based on the dev kit board with PCB antenna.
I flash SD110 6.0.0 and then I load bluetooth_hrm demo and there are no errors, but I dont see Bluetooth...
I posted another question along these lines, about using the Timeslot API to get observer behaviour with the S110 v7.0 SD, but I am having trouble getting it to work.
Are...
