Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
I have a nrf9160 DK but when upload SLM application to it i can not send AT commands to it over it's usb port but in asset tracker application it works i want to modify SLM...
Finally we got our prototype boards and proof of concept firmware code done and we are a bit stuck on the average power consumption over time for the entire sensor that is...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
Hi,
I have integrated Neuton’s “Transport Type Detection” pre-trained model into my firmware, running on a nRF52840dk. For collecting 9-axis IMU data, I’m using the ST X...
Hello Nordic Team
I am using SDK 3.0.1 with a nRF52DK to develop a firmware that can be switched from BLE mode to GAZELL mode and vice versa over a command sent via UART...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
I have built and installed bluez 5.21 on ubuntu 14.04 witout problem (see for example this recipe ).
My nrf51822 EK dongle PC10000 is not recognized by hcitool:
hcitool...
What exactly is block size in pstorage?
Desired block size for persistent memory storage, for example, if a module has a table with 10 entries, each entry is size 64...
I'm looking into using the CMSIS RTOS on the nRF51822 with the S110 softdevice which I've used successfully with other Cortex M0 MCUs. I realize the S110 isn't well tested...
Hello,
I am new to BLE shield and arduino stuff. I am working on a project where I have to send the sensor data i.e. temperature sensor, humidity sensor and pressure sensor...
Hi,
I'm using the nRF51822 and pCA10001 as SPI slave.
For reasons beyond my control I have to read the Rx Buffer before the CSN is released.
Yes, I know I shouldn´t do...
Hi!
Could I find somewhere (I was trying in Nordic docs and in previous posts but everything refers to previous versions of softdevice) how to perform bonding with key...
Hello,
When designing a 4 layer board with the nRF51822, should I connect the chip and impedance matching circuit to analog ground and keep the other digital chips isolated...
use nRF51822_Evaluation_Kit
I want to auto bonding by peripheral ,once peripheral connected with center(android app).
Is there have any API to send pairing request?
Hi, I tried uploading the example code from \nrf6310\spi_master_example to nRF51822 evaluation kit board, but no matter what I do, I always get SPI error. Not compile or upload...
Hi,
is there a nRF Master Control Panel equivalent App for iphone?
I'd need an app where I can set custom characteristic. The background is to update the device using...
I'm a begginer in embedded program. I have a mbed HRM 1017 that
is pin-compatible with Nordic PCA10004. .
I'd like to make a simple app to print out "Hello World" to terminal...
Hi guys,
How to update softdevice on mBED nRF51882 kit?
Details:
I have couple mbed dev kits with nrf51882.
I use Keil for development but will move to GCC after while...
Hello all,
I wanted to ask if there are any cad files for Eagle or other hobbyist level design tools for the nRF51 chips before I spend time to create and debug them? ...
hi guys,
I'm pretty new to nordic ble development, but I have a fair idea of the differences between EK, DK and the mbed enabled MKIT.
I'm trying to build a deploy about...
