Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
I have a nrf9160 DK but when upload SLM application to it i can not send AT commands to it over it's usb port but in asset tracker application it works i want to modify SLM...
Finally we got our prototype boards and proof of concept firmware code done and we are a bit stuck on the average power consumption over time for the entire sensor that is...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
Hi all, I'm using sdk11.0.0 signed bootloader and I have custom board with dfu support. The custom board have device type ex:0x01 now I need to change device type to ex:0x02...
Hi all,
i need to read the status on my GPIO where there is a led.
I have configured it like a:
nrf_drv_gpiote_out_config_t configLed = GPIOTE_CONFIG_OUT_SIMPLE(true...
Hi. I'm using nRF51822, SDK12.2.0, S130 as multi-link Central.
#define SCAN_TIMEOUT 10
Time-out is working well when it is Single connection. After 10 second, it stops...
How i can see the performance like the Picture. is allways 0% and had also no time or calls in the execution profile. Breakpoints works.
But when i press F10 (Step over)...
Hi There -
I'm trying to test connection interval negotiation with a central by putting nRF Connect Desktop (Mac) in peripheral mode and requesting a connection parameter...
I have a nRF52840 application that needs to take a complex list of commands from a server.
I have a few options. I could:
code a basic language myself for these commands...
HEllo
I am using the example TWI_sensor_pca10040 with a main.cpp, and I see that there is some sort of error with the logging that I cannot point out. I get this error...
Hi
I'm currently working on the 10028 DK board, which was working flawlessly until I used the J-link RTT Viewer, and pushed the IF BOOT/RESET-button. Now, when I try to...
Hey,
SHORT VERSION:
Timer (every Second) gets started when connecting (BLE with nRF Connect) to my DK (SDK12.2, Softdevice S132). Timer gets stopped when disconnecting...
Hi There,
We have an issue where our project crashes, but the app_error_fault_handler() callback is not being called to help identify the cause of the issue. We are using...
Hello guys.
I'm newbie to embedded programming.
I'm trying to make device that can measure temperature of other objects. I have a variable resistor. The resistor's resistance...
My BLE application uses my own firmware update algorithm and bootloader, as well as the Peer Manager module. To ensure that I do not delete peer data during the update process...
I am using nrf51 running as a peripheral and an iphone app as central. It works OK when I first use the iphone app to connect to nrf51. Then I quit the iphone app and let...
Application data is stored just before the bootloader. If I do a DFU upgrade with a larger bootloader than the one currently flashed, is this taken care of? That is, is the...
