Hi:
PLEASE CANCEL THIS TICKET
I'm doing exercise 1 of lesson 1 of the nRF Connect SDK Intermediate course. It says: Get the source code of this course as a third-party...
I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Hello
I'm trying to track lost packets in a connection by showing the sequence number of each packet received. Specifically it's about an application that sends new measurements...
Hello sir,
I have develop product on nRF52832 DK and now i using custom nrf52832 board Here . I want to continuously on my device with BLE advertising continuously no sleep...
Hi there,
In my SDK12- SD132 NRF52 app, I'm running NUS ok, and I want to add two more services. So, I made this changes at ble_stack init:
ble_enable_params.common_enable_params...
I am trying to add an extra service from an exiting nordic example code:"experimental_ble_app_blinky" into another exiting nordic example code: "ble_app_hids_keyboard".
...
Hello,
I'm encountering a very strange problem while attempting to run an fstorage fs_erase operation on my peripheral device when the central is connected. This is on...
Hello,
I want to make a device that use a Zigbee SoC and a nRF51822 for BLE, and I want to make it in the same board, that imply to have two antennas in the board.
I...
Hello,
This is Milav Form Teq Diligent,India.
I read the Bluetooth core 4.0 pdf.
In that they defined the " Park State " .
is this state are available in nRF51822...
Are any of the freeRTOS examples Power Optimized? I've looked into other related posts but not sure anyone is seeing the same issues I'm seeing. I'm using a Rigado BMD300...
Hello: I'm about to test out the ble mesh dfu, and to do that I need to flash my device, which is nrf52840, with precomped bootloaders.
Now here is the problem: Which one...
We need to certificate our ble devices. I use DTM example. Already I connected to device and flash example. Which correct command can I send from PuTTY console for check that...
I have trouble making iOS to reconnect after a device firmware update: I assume the issue
is due to flash being rewritten and so loosing information about the iOS peer.
...
I'm wanting to design a mesh system that will be running on batteries.
I need to keep track of the battery voltage. I don't plan on monitoring it often maybe a few times...
Hi All,
I am trying to interface an SPI OLED display 128x32 with my nrf51422 development kit over SDK 12.2.0 with BLE. After the program gets compiled, i am getting this...
I am designing a board with a host cpu and Nordic nRF52832 as companion chip in order to have Bluetooth capabilities; the two SoCs are connected each other through the uart...
