Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
Hi.
I wonder if you could help me:
I'm using a thingy91x and would like to work with the npm1300. In the case of this hardware, the PMIC npm1300's i2c bus is connected...
Hello,
For our project I'm using a LIS2DH (accelerometer) that is supposed to trigger an interrupt on its pin INT1 when a movement is detected.
I use nRF52832. Before...
Hi
I'm not familiar with C language, I tested the saadc example in SDK, it worked well in P0.02
But I dont see how they set CH[X].PSELP or CH[X].PSELN (V(p) and V(n))...
Hi
Using PCA 10040A , SDK 16.0.0 and Segger Studio.
I would like to generate a short accurate *** on a GPIO , probably 250 nano seconds duration. So I am looking at using...
Hello All,
my application should record acceleration data and time stamps.
After recording the data block from start to end should be transmitted.
I only know that...
Hello, guys.
In our current project, we need to periodically update AWS IoT Server with the data from local sensors. So far, thanks to the cloud_client example and your...
Hi
For a new project I'm looking for a cheap bluetooth chip. All my software resides in a PIC, because on PIC I have a lot of experience and I don't have the time to dedicate...
Hello all,
I am using NRF52840 and SDK 16 in central mode and added two UUID filters to the scan module for two different groups of peripherals . My application works fine...
Hi,
I am trying to send a test message in Server through mqtt and used the mqtt_simple example for that.
For the test I insert data_publish() function in main() like...
Hi!
The subject is most of the question.
I am beginning to customize the ble_app_template example, and when I build it, connect, and look at the advertising data, I see...
I want to connect NRF52840-pca10056 to PC via USB cable. I followed the docs but the OS doesn't detect the board automatically when plugged in. It only recognizes the board...
Dear Nordic Community We are about to develop a Testing-Framwork to compare different Mesh-Networks (Bluetooth Mesh vs. Thread vs. Zigbee) for which we would like to use the...
I've looked around on the forum and I can only find old posts about this.
Based on your repositories it seems like you support just about every big language except for Java...
Hi
I have a simple question which I am not able to figure out.
How do I use the nRF52833 DK without having it plugged to the computer. I tried switching the power to...
We are using a flash part that is 64 MB in size. It is S25FS512. We are trying to use 32 bit addressing mode by setting sdk config flags. However this does not seem to work...
