Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Hi,
to what impedance shall the BT antenna be matched?
Copying from the datasheet:
A matching network is needed between the RF pin ANT and the antenna, to match the...
Requests for the FW:
Add characteristic to access general GPIO pins in analog and digital form.
extension of the existing MOS_1-4 access, PIN read/write under the...
Hi,
We use nrf51 SDK v9. I found there are two SER_MAX_CONNECTIONS defined both in app_ble_gap_sec_keys.h and ser_config.h. Their values are different. One is referred...
Hello,
I have a problem when I try to use cheaper Android phones to communicate with our 52832 chip.
I can discover the peripheral and then connect, but when I device...
Hi,
I flashed softdevice and ble_app_UART_c code. But after searching bt device, i could not find bt nrf52 device in mobile.
Do i need to something more..
hi,
i am using nrf52840. with sdk 14.1. i am trying to broadcast my dk as beacon. with your neccessary examples. i have created my own services and started advertising. when...
I want to transfer data using UART to BLE by Baud Rate 460800 up to(using nRF52832).
I need to send a file, its size is 100MBytes
However, the use of examples(14.0vesion...
I would like to establish a BLE unencrypted link to send text messages. I have nRF52480, nRF51 USB dongle, and a mobile phone. I run Ubuntu 14.04 and Win10. It is not clear...
Is it possible to program the Atmel SAM D20E chip (based on an ARM-M0 cortex processor) externally using the P19 debug out header on the nRF51-DK?
Thanks.
I am trying to understand the Passkey LESC pairing on S140 soft device using the latest SDK 14.0.2.
The message sequence charts has a block "App starts DHKey calculation...
Hi developer, sorry to interrupt and ask. How to use an ultrasonic sensor with nRF52? Since I search a code for nRF52 are not exist and see ultrasonic sensor can connect with...
I modified TWI_SENSOR_PCA10040 example from 14.10 SDK to run on my NRF52832 device, and it reads from the device address perfectly. However when I wrap reading inside a FreeRTOS...
Hello ,
What is the preferable way to flash code into NRF52832 IC during mass production? Flashing the code into custom IC with NRF52-DK in time consuming process.
And...
Hi,
All of a sudden (isn't it always the case :) the JLink debugger fails to flash the app code to the dev kit (PCA100028)
The Project's softdevice is flashing well without...
I have configured 3 differential ADC channels
to sample with timer/PPI/DMA buffer.
When I turned everything off, I couldn't get below
20uA current (with only LFCLK running...
