I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Hi,
I can't manage with error in secure bootloder (from secure_dfu_ble_s132_pca10040_debug example) on custom board with nRF52832xxaa chip. I got a signature validation error...
Hello.
Nordic Team.
I add for ble Service and i select my service notify enable
I want receive my service number, but service number is different.
Add for my source...
Hello,
Nordic Team.
I don't understand 'ecg cccd_handle number ' 'p_evt_write->handle number' difference.
I add for ECG Service on my bluetooth profile.
ECG Service...
Hello,
In ble_app_uart_c example, I can see sleep_mode_enter() function. I would like to know when this function is called and what it does. I don't want my IC to get into...
I have a binary data file that I would like to program in flash at defined address on a nrf52 device
Which tool do you advise that generate hex intel file format by providing...
Hi guys,
I have a 4 thread freeRTOS setup.
BLE - priority 4
TWI - priority 3
LED - priority 2
Logging - priority 1
After running for some time my code always...
Hi. I'm using nRF52832, SDK13.0.0 as peripheral.
I set the values as below to advertise every 400msec.
......
adv_params.type = BLE_GAP_ADV_TYPE_ADV_IND;
adv_params...
I have two characteristics inside a same service - one characteristics notifies periodically and another on demand. I call sd_ble_gatts_hvx to send notifications with appropriate...
Hi all,
I got strange behavior: when I disable the SoftDevice (nRF52832, S132 V3.0, SDK 12.2) seem that ALL the RTCs, not just the one used by the SD, are stopped, and...
Hi.
I got the ble_app_beacon example to enter System On low-power mode (and operate in the 1 to 2 microamp range except when broadcasting). And I also got that example...
Rather than using previous timeslot examples for esb and ble multiprotcol, can we manaully switch between both protocol, what kind of process need to switch from ble to esb...
Hello,
I am building a project that required pwm drivers and BLE UART. I started by using peripheral ble uart example in SDK 12 and adding the pwm driver source file from...
I'm in need of some help with connecting to the Thingy 52 when using Windows 10, in this case Windows 10 Pro. I've tried Google Chrome and Opera.
If that helps, I have...
Hi,
I'm using sdk14.2 peripheral examples fds and fstorage in an attempt to test flash storage persistance (with softdevice present).
The two examples are quite intuitive...
Is there any way to invert the PWM behaviour easily? I'm trying to develop firmware that will run on the DK52 (LED active high) and my custom board (LED active low).
I...
