I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Hello,
How can I determine the current consumption of Bluetooth 5 use nrf52832 soc with transmission at -4 dm when in the datasheet mentioned only the current consumption...
Hi,
I've just got an Arduino Nano 33 BLE with the NRF52480 chip on it.
I've been trying to manage the Pin configuration by setting the register values through the Arduino...
Hi,
I am using a NRF58240-dk pca10056 S140.
I have an external SD card device connected which, I am writing live sensor data to then advertising that data over a ble advertisement...
Hi ,
The device required to keep advertising during the connection established.
It is human interface device which mean it is peripheral device as well.
I would like...
Hello there,
A while ago I started developing on the nRF9160DK but I found an issue that I do not know how to solve by myself.
I used two SIM cards: the one from iBasis...
._build\nrf52832_xxaa_s132.axf: error: L6002U: Could not open file ..........\external\micro-ecc\nrf52_keil\armgcc\micro_ecc_lib_nrf52.lib: No such file or directory
Hi all,
Is there any sample sdk example for transferring audio file from nRF52840 to my mobile? Is it possible to transfer audio file through Nordic Uart Service? Thanks...
Hi,
I am developing a product based on nrf52840 soc, I need to write a softdevice, program hex file, bootloader on the chip. when I want to select them all in the nrf...
I am trying to set up the LPS22HB sensor with an nRF52840. I am starting with the twi_sensor example(SDK16->examples->peripherals->twi_sensor) and adding the lps22hb example...
We have added custom HID firmware and are able to discover it on the Android Bluetooth Settings app. iOS fails to show the Bluetooth device on iOS Bluetooth Settings app....
Hi,
My task is..
Device will advertise for 20 seconds if there is no connection then it will go to sleep mode for 40 seconds. After 40 seconds it will wake up from sleep...
I have the nRF9160DK 0.8.3 which appears to align with the suggested schematic in "Objective Product Specification v0.7.1" I downloaded the hardware files form the Getting...
Hi,
To turn on and turn off the LED nrf SDK is using following code in sdk12.1.
#define LEDS_OFF(leds_mask) do { NRF_GPIO->OUTSET = (leds_mask) & (LEDS_MASK & LEDS_INV_MASK...
According to SIG's MESH Profile: "There is also a device key (DevKey), which is a special application key that is unique to each node, is known only to the node and a Configuration...
