Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
I have a nrf9160 DK but when upload SLM application to it i can not send AT commands to it over it's usb port but in asset tracker application it works i want to modify SLM...
Finally we got our prototype boards and proof of concept firmware code done and we are a bit stuck on the average power consumption over time for the entire sensor that is...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
Hi,
I have integrated Neuton’s “Transport Type Detection” pre-trained model into my firmware, running on a nRF52840dk. For collecting 9-axis IMU data, I’m using the ST X...
Hello Nordic Team
I am using SDK 3.0.1 with a nRF52DK to develop a firmware that can be switched from BLE mode to GAZELL mode and vice versa over a command sent via UART...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
By trial and error, I notice that I can only write 20 bytes to a characteristic, no matter how big I make ble_gatts_attr_t.max_len. A little googling reveals that this is...
Hi,:
I run my application program by nRF51822, about S110 V6.0 and SDK 5.2.
When the program run servial cycle functioin , it is work normail.But sometime, nRF51822 sysytem...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
Hello Guys,
I'm about to start my first BLE iOS project and I was wondering if there are any compatibility issues or anything that I should be aware between nRF51822 and...
im running on mac with eclipse and tried to use debugger prints, but the don't show up in the console.
Same goes for printf and uart.
Is there a flag in the makefile preventing...
Hello,
I am checking to see if it is possible to use app_twi_perform() to transmit TWI transactions that have a High Write bit. I have changed the polarity of APP_TWI_WRITE_OP...
I'm developing an embedded application using the nRF52 device. I am using GCC to build the C software and a segger flash device to program the nRF52, all using linux. I wish...
I wrote this code found in an example and it works fine:
#include "nrf_drv_config.h"
#include "nrf_drv_timer.h"
//Before I activated TIMER0, TIMER1 and TIMER2 in nrf_drv_config...
Hi,
I am using eclipse IDE and gdb to debug and flash applications onto nrf52 dk. I wish to be able to print data and messages to the eclipse console. I work on mac OSX...
I'm trying to send data over UART... started off using the examples from the SDK.
When I run the code on the dev board, I can get it working. When I load the code onto...
I want to use ESB protocol, with app_timer module to generate timer interrupts. Is it possible?
If yes could you please send some example codes for it? thanks
Per the nRF51822 product specification the NVMC ERASEPAGE operation takes up to 22.3 ms, about 730 ticks of a 32 KiHz clock. This is 365x the maximum delay between the watchdog...
For evaluating the nRF52 for a project I need to demonstrate BLE 4.2. secure pairing with NFC
I want to use two nRF52 eval boards but I need two software examples: One...
