Hi,
I want to add scheduler server to the mesh/light sample with nrf52DK, I change the element define like below:
static struct bt_mesh_elem elements [] = {
BT_MESH_ELEM...
Hi,
I’m working with an nRF52832 DK board that’s stuck in bootloader mode—LED 5 just keeps blinking. Here’s what we’ve tried so far:
Held the IF BOOT/RESET button...
Hello,
After I upload a new signed image to my device using MCUboot serial recovery (single image), MCUmgr Img_mgmt_client API
img_mgmt_client_state_read() always fails...
Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
tl;dr: UART transmission sometimes stops and never resumes. Only a
power cycle resolves the issue; a system reset is not sufficient. The
problem only occurs when flow control...
Hello,
as far as I have gathered, it is possible to use multiple peripherals on one device with the current alpha release of the S132 Softdevice. What I did not understand...
Hello,
today I had a problem where a timer was causing my device to reset after a while, because the app scheduler queue got full and it was raising an NRF_ERROR_NO_MEM...
Hi!
I am playing with NRF cloud and Android phone gateway. I am not able to find out how to carry out firmware update over NRF cloud. Would you please shed some light?...
I am developing an application with a single service that has a single characteristic with read and write operations.
I want to give the ability to writing to this characteristic...
Hello,
I am working on a project with STM32 master and nRF51822 slave connecting to Android/iOS mobile apps.
I send the advertising parameters from STM32 to my nRF51822...
Hi,
I am new to firmware engineering. I have a simple and basic question.
If there's Timer A and B, and both interval is 100ms, what happens to the timeout handler functions...
I want to add some configuration files to nrf52, so can I write data in flash and read when I want.......I have the example code of twi master_twi slave but it engages the...
I have followed the instructions for sniffing ble packets with wireshark. Errors would occur when using 2.2.5 so I switched to the latest development version. See this question...
Hi, I am developer of indoor location tracking solutions for asset tracking applications, actively looking out for new technologies, i would like to understand what are the...
Normally I am using nrf51 for peripheral(sdk 8.0.0 s110) and central(sdk10.0.0 s130) device. But I want to use nrf52 for just central device. I tried nrf52 for central(with...
Hello All
Currently i am using nRF51422-DK (PCA10028) Board .I am planing make mesh network using nRF51 devices.i go through the mesh network introduction document which...
Hi,
I'm trying to set a button as an interrupt source. I wrote this code:
void Init(void){
pwrmng_MainStatus = PWRMNG_STS_STARTUP;
//LED
#ifdef DEBUG_LED
nrf_gpio_cfg_output...
I want to read the status of LFCLK,but I find that ,the value I have readed is awayls zero! my code is follow :
LFCLK_State = ((NRF_CLOCK->LFCLKSTAT) >> 16) & 0x00000001;...
Hi,
I had done secure OTA in nRF51 DK board using SDK 12.2.0 and s130 2.0.1 softdevice. Now, i am trying to same thing with my custom Board RL-51822-A1.
For that first...
