Hi,
This is actually a follow-up to my previous question here: devzone.nordicsemi.com/.../publish-timeout-handler-of-one-model-called-during-publish-timeout-handler-of-another...
Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
Hello, I am building a power switch for my application and have some questions about expected behavior when holding a GPIO output signal at HIGH during System ON sleep mode...
Hello, I tried to merged two examples from SDK
1) I run ble_app_bps example from SDK 15.0 HW - PCA10056, nRF52840
2) I included to the main.c
3) I defined in sdk_condif...
Hello,
I am working on a little app running on nrf5340 app core. Now I want also to program the network core, to be able to exchange data via shared memory as little demo...
IMEI 352656100982084
I need your support to solve this matter urgently because we are developing a IOT solution to monitor several thousand motors - one Thingy 91 for each...
Hi Team,
We are using nRF9160 -DK (0.8.3), As per the document we followed the procedure from here . Loaded the respective application to the on board controller(nRF52840...
Hello
I try to use nrf24l01 in multiceiver mode for a domestic application
I made a simple set-up with 2 nrf24l. On the receiver i activated 4 pipes (0 to 3) with these...
Hi,
I have updated the modem to version 1.2, and connect sdk to 1.2, and now the SUPL library doesn't work? I'm using the GPS sample and it is getting stuck at "starting...
I have the mesh light switch on/off example running. What is the easiest way to test sending and receiving data from a non-mesh device to the proxy node? I want to be able...
Hi All,
I have programmed my nrf52832 device with DFU bootloader,softdevice and buttonless app provided by SDK. I am using SDK16.
My device is getting recognized by nRFConnect...
Hi:
The nRF52840 VDD voltage supply range is 1.7~3.6V
So if we provide 3.3V to VDD, the voltage ripple spec. is still 1.7~3.6V?
Or other spec. that we need follow? ...
Hi,
I am evaluating a BLE beacon solution and the nRF52 seems attractive. If building a solution where an appliance I will develop will listen for a BLE beacon that I also...
Hello,
I am new on keil and nrf, I am trying to merge nrf52832 sdk15.0 ble_app_hrs example and this custom service
I want to send command from nrf connect app to my nrf52832...
Hello,
I am working on a BLE application for the Thingy91 which needs a lot of dynamic memory. In the Zephyr specification values of up to 16kB are supported. I tried to...
I am using zigbee light_control examples in nRF5_SDK_for_Thread_and_Zigbee_v4.0.0 for my zigbee projection.I want to know how the zigbee network build and which command will...
