Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
I have a nrf9160 DK but when upload SLM application to it i can not send AT commands to it over it's usb port but in asset tracker application it works i want to modify SLM...
Does the nRF52 ( or anyother product ) support ASHA and MFI audio streaming?
It looks like ASHA is supported, I found this:
https://github.com/nordic-auko/nRF52-ble-audio...
Hello,
We're bringing up custom hardware using SiT1532 MEMS 32kHz oscillator. This part outputs a low swing single ended clock source (300mV +/-55mV p-p). I'm struggling...
So we are creating a peripheral with a characteristic meant to keep the central synced with the state of our peripheral. The peripheral is running all the time, could be ON...
1. This is on the stock LPN example, with one change to debug-print `status_code` inside handle_appkey_add().
Here is the diff:
2. To reproduce:
- flash and provision...
Hello,
I am currently working on a product with nRF51822 chip, based on SDK10.0.0. The problem is, after a firmware update, my device fails to reconnect to an Android mobile...
Hi,
I've launched wireshark + nRF52 Dongle successfully and I'm also able to select my device (named EWAT AI-No) from the list to sniff. However there's something I don...
I'm working on a simple project based on the USB CDC ACM and libuarte example, the chip is nrf52840.
A function is redirect the USB VCP data to another MCU via UART, just...
Can a server and a client of dimming example, have same element instead of different element ID.
I got worked for server and client model in single node, but they are in...
I am upgrading to SDK 15.3.0 and SoftDevice v6.1.1 from SoftDevice v2.0.0 (S332 stack). Most of functionality has been ported (BLE and ANT) and validated. This particular...
Hi, I'm trying using a setup with transmitter based on nRF24L01P and receiver with nRF24LU1P using Enhached Shock Burst. The problem is the transmission lock (three failed...
Hi,
I am planning system with a BLE peripheral (using nRF52840) and BLE Central (using nRF52840) that is AC powered.
The peripheral will be advertising every ~300msec...
Greetings,
We have some custom boards/devices with nrf9160. They each hold certificates to communicate with aws-iot. The certificates were flashed using the at_client...
Dear nordic,
I am developing a robot controller(Central, nRF51822).
However, I am having a problem with UUID.
And I am using the ble_central (s130 ble_app_uart...
Hi,
I am using nrfutil to generate a bootloader ota package for NRF52832 soic. The command I am using is
I measure on my ubuntu pc, when this command is...
When I was running the heart rate example, I would report this error below, someone tell me what caused this error, which causes the driver to fail to recognize now. But I...
