Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
I am using the Nordic 52840 CSP for my project. It is used for a asset tracking application. I used the nRF52840 QFN schematic reference for design. Since there is a difference...
Hello,
I am looking for the inband image frequency for the NRF51822. I have received a few different results and want to confirm what the value is if it is Low 1Mbps: +1...
Hello Nordic,
I have seen a couple of your reports and I am not sure how to read the inband image frequency. You have put frequencies in there (I thought values should be...
Hi
What is exact difference between following versions of nrf51822QFAC chip 1.nRF51822-QFAC-T 2.nRF51822-QFAC-R7 3.nRF51822-QFAC-R
I am searching for nrf51822-QFACAx chip...
Hello
I am trying to move an arduino project where I read an ADC value from a FSR sensor. In arduino the FSR is powered by 5V and has 10Kohm pulldown resistor. The board...
hi,everybody
I want to design a sniffer for 2.4G raw data，I have some problem below
1.How can I set the radio register to recieve all message on same frequency；
2.I...
I want to create a PCB circuit withe the nRF52810 Transceiver. If you do not understand what i have in mind:
http://si.farnell.com/nordic-semiconductor/nrf52810-qcaa-r7...
We are seeing a potential issue with a product. on start up a pin is read and the read value determines if we go in to a test mode. Pretty standard.
Our failure is during...
Hello
i just bought my DK-nrf52 to move to BLE after playing few months with arduino. I have connected various nrf52832 shields from China (from Holyiot 17095, which is...
Hello, I want to test Round trip delay using BLE MESH 2.0.1 Light Switch Example Code...I have modify simple on off Light Switch Example. Example test using two Development...
Scenario:
We have three verticals in our project. The nrf51822 based device, base station (BS) and server running on cloud.
Problem Statement:
I need to continuously...
I have downloaded "nrf5_SDK_for_Mesh_v2.0.0" yestoday, and try to setup the "light_switch" demo with 3 pic nRF52 DK.
According to the document description, “proxy_server...
Hello,
I have a query regarding the implementation of multiple user-specific GATT profiles in our application.
For example, can we add two profiles like Heart Rate Profile...
I am migrating from SDK v14.2.0 to v15.0.0 and from S132 to S112 (v6) using the NRF52810. I have mostly everything migrated, but a functionality that worked before does not...
