Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
hello
i am using nrf52840, with BME280, i have external pullup 10k resistor.
how i can disable the internal pullup resistor.
i am using this sample code.
github.com...
Hi,
I am having problem with setting up TX side of my project. It always giving me max_rt error if I am sending only once per cycle. 1 Cycle is every 30seconds. All working...
Hi,
I use the SDK12.3 and SD130 with secure_bootloader and my own application. I can flash SD and Bootloader and update my app over OTA with DFU from NRF Toolbox. My app...
I noticed that when upgrading to the latest Thread SDK that my devboard stopped booting. I was following the instructions as per the documentation but noticed that my user...
Hi,
I am designing a custom PCB using the nRF51422. I want to include an external 16 MHz crystal oscillator to use as X1 according to the reference layout for custom PCBs...
When I test the timer example with nrf52832 DK, it so nice to 4 minutes.
uint32_t time_ms = 240000;
But when I set the time interval over 5 minutes, then the event...
What is the maximum number of bond table entries a device can have?
If a device allows only one connection to be established at once (not more than one simultaneously)...
Hi,
I want to store the CRC of the current firmware in the flash, for DFU purposes. Almost all of the threads I've seen so far reference the pstorage API but it's no longer...
I am searching for a basic example to understand the build system.
How do I load the soft device properly?
How do I set things up to run SEGGER_RTT_WriteString?
I...
I am using Nrf52832 sdk 11.I want to update the value of characteristic on every read operation from my andriod phone. I want that on every ble_gatts_evt_read: should give...
Hi! Im trying to figure out the power consumption of two types of beacons that uses nRF51 and nRF52. I have connected a small resistor in between the supply and measuring...
Preferrably under linux using gcc and the command prompt.
I am most interested in project setup, loading the soft device, and making sure all the core systems are working...
I am running the ble_app_uart example in SDK 13.0 with nRF52382.
First issue
The app can receive data via UART only when I use "Termite" as a terminal emulator...
