Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
Hi.
I wonder if you could help me:
I'm using a thingy91x and would like to work with the npm1300. In the case of this hardware, the PMIC npm1300's i2c bus is connected...
RTT log output issue
Hello, I am using SDK v3.0.2 and toolchain v3.0.2. After building and flashing my firmware, no logs are being output to RTT Viewer. What should I do...
I am generating a pwm signal in pin no:21 of nordic nrf51422 board. i connect this pin to pin no:24 using a wire in the same board and want to count only rising pulse edges...
How to decode opus file on Android or how to configure NVS on Android?
we have a Android TV device to connect Smart Remote 3 of nRF52，but audio from the Smart Remote is codec...
I am just trying to program my sample nRF52810 using a PCA10040 devkit.
I get the message "No device detected, or readback protection may be set"
Pressing the Recover button...
Hi,
I'm working on an application with an accelerometer without SoftDevice (for the moment).
The accelerometer communicate in I2C. It send an interruption when a new sample...
hi
I develop nrf52832 based ble device, this based rtos therefore ble communication have critical
time limit.
I will use mesh protocol my ble device, in the environment...
GLS is implemented using Nordic(S110_7.0_SDK6.1).
When set to Control solution function.
The setting of the device and the READ value of the application do not match...
I am trying to integrate an iBeacon Library on nRF51-xxAC with SDK10.0.0 and S110v8.0.0 . Can anyone please help me out if any one has ported the iBeacon Library and what...
I want to implement one central device to ten peripheral devices connections.
I'm using nRF52832 DK and S132 5.0 and SDK 14.0.
So, I have run multilink_central example...
I managed to sniff Nordic mesh sdk 0.9.2 packets on raspberry pi 3 using "hcidump --raw", and I can read the raw hex data of mesh packets of light control demo, but since...
Trying to interface this module with atmel core micro.
We are able to transmit data by this module but not receiving the data at other end.
At transmitting side we are getting...
Hi,
Currently I'm working on nRF52 with SDK11 and SoftDevice S132.
Till now I've worked with IAR and my code was based on the "ble_app_uart" and the dfu "bootloader" examples...
WHAT EXACTLY IS THE PURPOSE OF PPI. IF I AM GENERATING A PWM SIGNAL IN PIN NO 21 AND USING A WIRE I CONNECTED TO PIN NO :24(BOTH GPIOS) IN NRF51422 BOARD AND WANT TO COUNT...
Hey I was using the relay example in SDK 12.2 on the s132 NRF52DK.
We added a service and characteristic using the Nordic tutorial - devzone.nordicsemi.com/.../
Using...
I have a very simple test script which enables a BLE service (only the Generic Access and Attribute), advertises and waits for connection. It also sets four pins to input...
We made a READ request from the client with nRF 52 as BLE peripheral.
READ was automatically repeated 10 times when writing 200 bytes of data in a characteristic fashion...
