When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hello everyone, I've been trying to solve this problem for several days.
Hello everyone, I've been trying to solve this problem for several days.
I have developed a custom...
Hello!
I make peripherial device with some custom services. It is connecting with smartphone. i need secure access with it with passkey (pin code).
My last result is when...
I have one Service UUID and its only two characteristics UUID which is Tx (App to BLE) and Rx(BLE device to APP) to get different type of data e.g. Heart rate, Sleep data...
Thanks for your help עוטד. I want to use BLE / beacon technology in order to track items that pass-by in high-speed and close proximity (0.5m). This means I only have a few...
Hi,
I am using ble_app_hrs_c as the base for central. I have included 5 characteristics in the peripheral and central side. How to make ble_nus_c_rx_notif_enable() to notify...
ble_gap.h Hi,
At the moment, when a link loss is detected (in a connected mode), it takes around 3 seconds for it to be identified (with DISCONNECTED event). Is there a way...
Hi,
We are using system-off mode to save power in our device which uses nrf51822 chip. Our application requires regular wake-ups using RTC interrupts.
But the wake up...
Hello!
I know that nrf51822 beacon advertising packet consists of the following seven data fields:
Vendor ID
Service
Data payload size in bytes
UUID – manufacturer...
I would like to develop a BLE keyboard using nRF52832.
If you know the example source code, please let me know.
And can USB BLE Dongle for Desk-Top PC use the following...
Hi team,
I am trying to figure out how mesh network works. I do experiment with nrf52832 develop board and nrf5_SDK_for_Mesh_v0.9.2-Alpha. After I flashed light_control_server...
I have an app that requires BLE stack to be re-initialized, however it seems that if you run
ble_dfu_init();
more than once, it crashes
Upon further inspection...
Hi all,
I'm working with the nRF52 and I'm trying to run the heart rate sensor example from SDK version 13.1.0 using Crossworks as my IDE. I can compile and run the program...
Hi,
The below results indicate the nRF Connect app requires a handshake even when scanning without connecting. Is this true?
I am using the android 'nRF Connnect' app...
Are there any known issues with the nRF USB on the new chip or dev kit? I bought a dev kit to test out the USB functionality, but was unable to get any programs working. No...
