I have enabled data ready interrupt bit and also enabled the fifo bit and also enabled gyro_fifo and accel_fifo bits in mpu6050 so that when data ready interrupt occurs the...
I will be selling various ble products. My customers can connect to and program the devices using their bluetooth smart phone or tablet.
I want them to have the option...
Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
Related to SDK 12.3.
Quoting this question :
GPIOTE PORT event generated on the
rising edge of DETECT signal. Please
have a look at section 15.1.2
2)DETECT...
Hello,
I am experimenting with sending large notifications from an nRF52 configured as BLE peripheral with SoftDevice S132 v5.0.0. I having some trouble receiving the notifications...
Hello guys,
I would like to execute code once a scan request from any other BLE device is received by the NRF52 using Zephyr.
Unfortunately, I am not able to receive...
Hi everybody,
I have an issue with my application, I want to use the ble with the same antenna that it use in the development board PCA10036,
Could you please tell me...
When I send 512 Byte from my Android phone I received only 20 Byte. How I can received more than 20 Byte? I used example project "ble_app_uart", SDK 14, SoftDdevice s132,...
I am working with SDK 14.0 . I see two "type" of advertising_init() function :
1-
static void advertising_init(void)
{
uint32_t err_code;
ble_advertising_init_t...
Hi
I have successfully run the light control example for BLE mesh. Now if I want to add another server to the network, how do I do it without bringing the server in the...
I am using the ble_app_uart example from SDK13 and something strange is happening. The code without UART part works nice and I can see in RTT that it can discover every beacon...
Hi everybody,
I have an issue with my application, I use the nRF52832-QFAA with the following circuit, when I open the application Nordic 'nRF Connect', I detect the ble...
We have a software application for the NRF52 with BLE communication. The communication part is based on nordic example “ble_app_hids_keyboard”.
We are using Softdevice...
Hi there,
I am using the uart example with SD130 and added neopixel code from GIT to drive the WS2812B LEDs using bit banging.
I want to update the LED every ms. The bitbanging...
I am getting random data while using saadc example to reading analog voltage applied to pin on nrf52840. i want to read analog output from MQ135 gas sensor, I have applied...
Dear all,
by looking at the sdk code, specifically that of s132 component, I understand that the length of the PIN code is statically set to 6 and cannot be changed.
...
We have been using nrf24l01+ for sending few bytes between one Master(Master MCU board) device and many slaves(slave MCU boards). Each time Master Device queries data from...
I installed nRFprobe driver to program and debug my nRF24LE1 chip from Keil. I am using a nRFgo 6700 starter kit for flashing and debugging purpose. I connect ISP connection...
