Hi all,
I’m working through Lesson 1, Exercise 2 of the Nordic Academy course (uploading the Blinky app to the Thingy:91), and I keep hitting this error: Firmware: C:\myfw...
I am using mcuboot with the child image functionality. my app should work for nrf52840dk and nrf5340dk. I want to set up the configurations so that for each board, the right...
Hello,
I'm currently using Visual Studio Code with the newest SDK, Toolchain and Plugin on MacOS and most of my applications are freestanding applications.
Now I want...
Hi,
I’m trying to use the SoftDevice Controller in peripheral-only mode on the nRF54L15 (using NCS 3.0.1), but I can’t get it to build with `CONFIG_BT_LL_SOFTDEVICE_PERIPHERAL...
Hi,
I want to add scheduler server to the mesh/light sample with nrf52DK, I change the element define like below:
static struct bt_mesh_elem elements [] = {
BT_MESH_ELEM...
Hi,
I’m working with an nRF52832 DK board that’s stuck in bootloader mode—LED 5 just keeps blinking. Here’s what we’ve tried so far:
Held the IF BOOT/RESET button...
Hello,
After I upload a new signed image to my device using MCUboot serial recovery (single image), MCUmgr Img_mgmt_client API
img_mgmt_client_state_read() always fails...
Hi all,
I am using NRF24LE1 32pin.
Does anybody know can I apply on XC1 pin external frequency different from 16MHz if I am not using radio module??? Thanks.
I am currently using the nRF51422 DK along with the nRFgo Starter Kit. I followed the instructions in the PDF "nRF51422_DK_UG_v2.0," and I attached the nRF51422 with PCB antenna...
use keil to download code to flash fail
use nRFgo studio to connect target device error
Load
C:\Keil\ARM\Device\Nordic\nrf51822_v5.0.0.34603_Backup\Board\pca10001...
Hello,
when using Keil's ULINK Pro debugger V1.57 connected to PCA10006 board for debugging nRF51822 code the ULINK is recognized by µVision V5.1.0.0 but the FW download...
I have an nRF51822 (256KB) that I want to program with some data targeted at 0x20000 to just under 0x38000. My code starts at 0x16000 (allowing for S110) and is only 1700...
I have a nrfgo 6310 start kit that I use for my nrf51822, but I'm wondering if I can also use the nrfgo 6310 for the nrf24Lu1 development kit as well? I tried plugging in...
Hi All,
I am working on the S120 bootloader.
I start it with dfu sample on nrf6310 folder. It work with S110 softdevice with PCA10001 perfectly.
I had made following...
Hi,
I would be grateful if someone could guide me a bit.
As far as I understand, nRF24L01+ implements Enhanced Shockburst technology in chip. To use nRF8001 as drop in replacement...
Hi all,
I am using s110 v7 for scanning and advertising, it works well. Now, I would like to measure RSSI while scanning (already scanned device but not connected) . Can...
Hi,
I am using nRF5182. Kiel is the IDE. I need to operate the device in 25Mhz. How can i change the clock frequency to 25Mhz. Is it possible? Will it affect the operation...
Hi,
I just stumbled upon the nAn-36 note ( www.nordicsemi.com/.../80193304 ) and I have two comments about it :
I think it's the best technical documentation I've...
Where to find definition for INTENSET/CLR for TIMERs in 'nRF51_Reference_manual v1.1'? I think I've read it all by now, but still can't find it.
After some digging I found...
If I have the PC insert 1msec byte spacing between data bytes sent to the NRF51422, it receives the message and doesn't reset. I can send messages less than 10 bytes to the...
my code shows here: github.com/.../main.c
uart_init();
printf("\r\n\r\n");
printf("\r\n __DEBUGGING__\r\n");
every time my app started, it always shows corrupted...
Is there any more information available on a release date for the next rev of the 51822 which is supposed to have better handling of concurrent A/D and radio operations? ...
