Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
I have a nrf9160 DK but when upload SLM application to it i can not send AT commands to it over it's usb port but in asset tracker application it works i want to modify SLM...
Finally we got our prototype boards and proof of concept firmware code done and we are a bit stuck on the average power consumption over time for the entire sensor that is...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
I'm testing a data collecting program which samples data every 2s and reports it through UART ( printf("data=%d\r\n", data) ) on a PCA10001 board. I found this program may...
Hello,
Got a question about nRF51422 and S310 stack. I am trying to understand how the radio is being handled and how the softdevice handles events in a specific case....
I tried communication between PC and my own board(nRF51822) PCA10000 usb dongle&MCP, I found that the first time I send n(where n is any decimal number) bytes data(s) from...
Dear Nordic guy,I'm developing with nrf51822 (6.0 stack binary and 5.0 SDK).
I recently updated the code and stack binary(6.0 stack binary and 5.0 SDK).
My function is not...
static conn_mw_handler_t conn_mw_handler_get (uint8_t opcode)
Inside the function,
for (i = 0; i <conn_mw_item_len; i ++)
{
if (opcode == conn_mw_item [i] .opcode...
It seems like it should be easy, but I've spent a fair amount of time and haven't found a way. I only see options 5.0.0 and 5.1.0. There are also links to earlier SDK versions...
Hello All,
Sometimes is fine to use a forum but sometimes we have to meet a deadline and the forum questions don't always get answers for in a timely manner.
So I'm...
I would like to use Channel 0 of the S310 Stack V1.0.0 on the nRF51422 to do a background scan of ANT devices.
I am testing against ANTWARE II v4.1 with the ANT+ usb dongle...
Hi,
I'm working on the ble devices to transmit sensor data using s110 and s120 with one connection.
I want to send 6 packets for every 7.5 ms connection interval from the...
I have been to a number of Nordic events this summer, and it was hinted / suggested / unofficially announced that there would be a third SKU of the nRF51822, that included...
Hello,
I am creating a PCB design for NRF2402AG but I'm not sure whether I should connect pad under the NRF to the ground or I should left them isolated. I could not found...
Hello
I get this error when I try to program the module:
Parsing hex file(s).
ERROR: Cannot find C:\Nordic Semiconductor\nRF51 SDK_v6.0.0.43681\Nordic\nrf51822\Board...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
Hi dear friends from Nordic Semi,
I´m in great trouble trying to make these nRF24L01+ to work, one unit as a transmiter, and one unit as a receiver, it can be to send 3 bytes...
Hi,
I am using nRF51822 Evaluation Kit along with keil uvision4. Will using optimization in keil IDE make any problem in the normal working of BLE project? Will it affect...
