Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
I think I understand what these two flags do, the SYS one returns the system attributes, which I assume means data representing the CCCD for the service changed characteristic...
Hello,
Is there any compatible arduino lcd with existing library for the nRF51 Chipset?
So I can just plug it on the nRF51-DK, include the library and "lcd_wirte("text...
Dear Developers!
I'm a newbie in nrf51822
My Project needs to change between central and peripheral role. How can I apply OTA DFU with S130 soft device ?. In nrf51822 DFU...
Hi,
I used PPI module and Timer2 to generate a 4Mhz pwm. But I founld when using softdevice(s110 v7.0), the pwm will be broke a while by BLE advertising or connecting event...
What's wrong?
Device is connected. (nRF51822 Board - J Link - PC)
I downloaded a sample project, and when I open with Keil, then it shows following message.
What...
Hi all,
I would like to know which is the most recent SD and SDK that I should be using with my REV2 chips. In the compatibility matrix, there is no info about the SDK...
I am working on s120(central) and s130(central/peripheral). I am getting
BLE_GAP_EVT_CONN_PARAM_UPDATE_REQUEST event after updating conn_parameters w.r.t to peer using sd_ble_gap_conn_param_update...
Using nRF51x and S110 v8 in a BLE application I want to generate a random 32 bit identifier and store at end of UICR on first power up only after factory flash (no erase needed...
The pwm library seems to add 10KB worth of code to my program. Alot of it probably comes from the nrf_drivers that are used, but still 10KB. While enabled it seems to pull...
Hello,
Since 2 weeks, I use heavily my nRF51-DK (PCA10028), with mbed compiler to make a BLE enabled device.
But, since few days, when i have tried to cut the SB9 in order...
I have a Rev3 nRF51822 chip (CFACA00) on a custom board (no external pull resistors on SWDIO or SWCLK), and I am using nRFgo Studio 1.20.0.2 to program SD 8.0.0 and my Nordic...
I'm using Python bindings 0.5.0 and the connectivity app. On one of our machines that is running tests with the satck/dongle we see it fail a lot with a scrolling of this...
