What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
I used to be able to see my development kit in nRFgo studio and flashed S110 onto the chip. Now all I see is: "No boards connected". I am still able to flash programs onto...
Hello,
I have an iOS application communicating with a custom device having a nordic 8001 chip.
They have established a bonded relation. In nRFgo Studio, in Security...
Hi there, thanks for your help in advance!
I have tried the nrf51-ble-ancs-nus sample from github and making it work on a 51822 EK board, i.e., it can receive notifications...
I try to use hcidump, capture CSR dongle on ubuntu14.4.
I can find SDK8.1.1 s110 keypad demo create connection fail.
HCI Event: Command Complete (0x0e) plen 4
LE Set...
I want to experiment with recording observations of the beacons with raspberry pi's.
Is there any precompiled firmware I can install on the nRF51822 smart beacon...
In my application, I use the peer manager that has called the fds_init function, should I call it again if I want to use the fds to store my data. Will the peer manager use...
Hello Everyone,
I am using Nordic's Power Profiler Kit to estimate the current consumption of an external board. I have been able to configure it properly and getting results...
On nrf52840 I get a current of ~10 uA while sleeping. At the moment I don't run any code and don't start up the softdevice. I go directly to sleep with __WFE(). The result...
Hi All!
Faced with big problem with SCANNING procedure (nRF52840)
We have a BLE network : one CENTRAL and up to 6 PERIPHERALs can be connected simultaneously to the CENTRAL...
I want to detect high to low transitions on 28 GPIO independently. I've read in other posts you can configure 4 pin interrupts or a port interrupt for all pins, but I'm not...
Hello,
I am currently experiencing some problems, when i try using RTT output and the internal clock.
When using an external crystal, everything is working.
The following...
I am working on Ble tutorial of serivces, In step1 they mentioned to declare m_our_service of type ble_os_t. how can I declare that ?I am not sure to consider m_our_service...
Hello
I have been trying to use this repository: https://github.com/NordicPlayground/nrf51-ADC-examples and upon building, i get several errors due to certain header files...
Hi,
I have a Serialization connection working between a Nordic nRF52 CPU (slave) and an NXP CPU (master), using SPI.
The NXP is starting/stopping a BLE Scan on the Nordic...
Hi, I have some questions about the memory map, ram usuage and linker config for the secure bootloader when used with the S332 (4.05 sd_req 0x94) softdevice. I have tried...
USB Virtual COM
Until now, the development has been done by sending the commands via a USB virtual COM. The received buffer of int is processed and sent to the function...
I have an nrf52832 connected to a UART-USB driver with RTS/CTS. CLI manages the UART connection. Using SDK 14.0.
When HWFC is enabled, if a serial connection is NOT established...
Hi, p0.06 is always high lever when the following codes are executed:
nrf_gpio_cfg_output(6); nrf_gpio_pin_clear(6);
Why?
Softdevice is used in the project.
I have searched through the examples and the documentation (BTW the online document links are broken - the offline documentation is nice however).
From what I can tell...
Hello Everyone.
I am doing a project where I need to do a Bluetooth communication of data. I have two nRF51 DK so the idea is to connect a particular pressure sensor to...
