HI,
I am using the nrf_desktop sample in NCS V3.0.2, I want to buil with prj_release_dongle.conf , the setting
but build fail, I check the file Path: it should be F...
Hi:
PLEASE CANCEL THIS TICKET
I'm doing exercise 1 of lesson 1 of the nRF Connect SDK Intermediate course. It says: Get the source code of this course as a third-party...
I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hello,
I am using the NRF52-DK softdevice 6.0.0 and NRF SDK 15.0.The app is based on on the saadc PCA10040 S112. I want to add static const nrf_drv_timer_t m_timer = NRF_DRV_TIMER_INSTANCE...
Hello I am in a development stage
1. MBN52832 soc
2. s132 softdevice
3. nRF5 SDK v15.2.0
4. SPI PHY
So my concern is I want to port serialization library for SPI...
Hi, I hope it is fine to post a question like this since I'm not familiar with the license/copyright issues.
I have a friend of mine who wants to post BLE lectures using...
Hi, all.
I m trying to combine two example spi + timer using nRF52832.
But spi_event_handler function in the ex spi and timer event in the ex timer are crashed.
...
hi,
how can i scan for other BLE advertisments on nrf52811? there is no official documentation showing how to have Central role on nrf52811 softdevices! and no support in...
Can I still use the USB while the nRF9160DK is set up for current measurement as described in the spec, where power is applied on P28 after cutting solder bridge SB43 and...
I am using PCA10090, version with active GPS (tested using GPS sample)
I tried configuring using:
vi /nrf_root/ncs/nrf/applications/asset_tracker/build_nrf9160_pca10090ns...
OS in development environment ：Windows7 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
According to this thread, GPS sensitivity of Thingy:91 does not seem to be good while I haven't tested this yet.
https://devzone.nordicsemi.com/f/nordic-q-a/51424/thingy91...
Hello.
I have found this document and have a question.
In according with document below: service " Generic Access" (UUID1800) has a few characteristics: " Device Name...
We're attempting to get a Bluetooth data stream set up on our nRF52840. We've taken Zephyr's peripheral sample and pared it down somewhat to only allow indications from the...
Hello,
I am working on LPN node code from the mesh SDK 3.2.0. When I run the example code, I see a current peak at every 2 sec interval. Please check the image attached...
Hello,
I managed to flash the AT command client to the board and connect to a network (both verified by COPS and CEREG)
Am I right that there is currently no AT command...
