I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Hello, I build a BLE 6LoWPAN environment on my raspberry pi with Kernel 3.18.3 and connect a BLE Dongle. The BLE Node is Arch BLE ( www.seeedstudio.com/.../Arch-BLE-p-1998...
Hi, I have two different types of nRF24L01+ modules, both behave differently.
The "troublesome" module always has TX_DS asserted after a transmit, which is the same behavior...
Hi,
I am using the SPI Master 1 to control an EEPROM. I used the spi_example project to help get the code working. It all works fine if the code that initiates the SPI...
We have designed a differential antenna for the nRF51822 CEAA chip.
Each of the RF output connects through a matching circuit to each one of the two 50-ohm to ground end...
How to setup MQTT for CloudMQTT? I have working raspberry PI I can ping and connect to device when follow the user guide. Now I like to try MQTT example but don´t know how...
Is there a list of every interrupt these functions effect. Specifically I am worried about
static void ble_evt_dispatch(ble_evt_t * p_ble_evt)
My assumption is that...
Is there any S110 demo with good communication between periphera and APP in phone side in SDK 6.0? It means that data channle works well from 51822 to APP and APP to 51822...
Is there any S110 demo with good communication between periphera and APP in phone side in SDK 6.0? It means that data channle works well from 51822 to APP and APP to 51822...
The nRF51 series reference manual v3.0 documents 3 Real Time Counters: RTC0, RTC1 and RTC2 (pp 17 and 109). However, RTC2 does not appear in the SDK documentation (e.g. no...
when I download program(pin_change_int_example) in nrf51822, Immediate Interrupt is occured
And when I push the button, Interrupt is stop...
What is problem?
I want...
Hello,
I am designing a board based on the SoC nRF51822. Since this is a homemade project I do not have lab equipment so I can not measure antenna impedance and therefore...
I'm trying to pull my project out of the examples directory, but there seems to be many dependencies on files far outside my project, and files not shown in my project file...
We use Laird BL600 module in our design. Laird engineers has informed us, that to update softdevice firmware of Nordic nRF51822 chip inside module they use Jlink adapter over...
Hello,
i've already read a lot about this topic in this forum, but now I'm unable to continue on my own. I wan't to migrate the DFU SDK emaple from Keil to GCC. I already...
