Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Using nRF51822, I define keys and pins as follows:
Keyboard key
Mouse left/right key
Mouse move (up/down/left/right)
Media play/pause key
Pin 0 Mouse...
Hi
After the device has been in idling, the sleep_mode_enter function is called which then calls
sd_power_system_off().
The device then goes into sleep mode until a...
Hi! I need your help!
I need to create some mesh network consists of simple devices (A) which could collect mac addresses of all visible Bluetooth devices (C) and send it...
Hi, I try to mount some I2C devices at Arduino Primo but I can not get any results. I tried an I2C LCD that did not return any error but did not display any text. When I scan...
Hi,
I am using IAR for the pca10056 with a nrf52840 chip. Can I change the compiler in IAR? I simply just downloaded the newest version from the IAR homepage and specified...
Hi I'm trying to compile the experimental_ant_bootloader for the pca10040 with a S212 soft device using the armgcc compiler using SDK13
I can't find a makefile or linker...
How do you do
1.In the Nordic \ nRF5_SDK_12 _f012efa 2.0-3 d \ examples \ peripheral here, there are three PWM routines:
Low_power_pwm, pwm_driver, pwm_library but only...
Hi, there~~. The PCA20006, nRF51822 Bluetooth Smart Beacon Kit, is fascinating!
So I'm planning to create a custom beacon product of my own,
a 2-layered PCB with nRF52832...
I have trouble programming the PDK using nrfjprog. I can flash the program fine using Segger Embedded Studio but it doesn't appear to be working using nrfjprog.
Here are...
When using ble_app_uart, I set the advertising timeout to 10s, but after the timeout did not enter sleep, but automatically reset,my judgment is based on the terminal to send...
Hi
I have run this example code
nrf5_SDK_for_Mesh_v0.10.0-Alpha_src\examples\light_switch\client\light_switch_client_nrf52832_xxAA_s132_5_0_0.emProject
when I operate...
I want to reprogram a nRF51822 xxAC device on a existing product.
I have a J-Link (SEGGER) device with latest firmware.
I'm running the SEGGER J-Flash V6.20e utility.
I...
Hello,
I have constructed a custom board with nRF52832 and MPU9250 on it.
I have flashed the program for reading battery service, temperature service and MPU9250 readings...
I followed the tutorial on devzone.nordicsemi.com/.../ to use Eclipse, GCC and GNU Debugger.
I encountered an error after the successful build (with key symbol) with CDT...
Hello,
I purchased nrf51822 module and i want to use s130 sdk for my project.
But when i have look over using keil i found that it requires jlink debugger or jtag debugger...
I am studying about developing a simple BLE 6LoWPAN network. My proposed topology is mentioned below:
internet - - - - - - - - - BLE1 - - - - - - - - - BLE2
| \
...
