Hi there,
We are using for BLE communication a nRF52832 chip with random static address configuration (shown in the UART). Can we be sure that the address of a chip will...
I am building an application for the nRF52840 on Linux just using west . I have been struggling with this issue for some time now. The linker can't find any mbedtls_ccm functions...
Hello, I am experiencing issues with the current measurements taken by the PPK2 when using the nPM2100-EK to power a device. The current drawn from the 2.7V power source ...
I have been trying to get MQTT+TLS to work on the nRF7002 DK and haven't been able to get the samples to connect to the MQTT Broker.
Is there a working MQTT TLS example...
Seeing the failure below and wondering a couple things:
How did the device get into this state?
How do I disable AP protection? The Kconfig GUI seems to indicate that...
Hi all,
I'm working on a custom board based on the nRF9160 and using nRF Connect SDK v3.0.2. We’ve developed the board in-house and integrated the npm1300 PMIC as part of...
Hello,
For our emission tests in an anechoic chamber we need to be sure that the BT antenna is up and running. Of course we cannot connect via BT from outside the chamber...
I have a BLE wearable (Pebble watch) that I wish to detect using the nrf51822 evaluation kit. I can use the Control Panel to see the pebble. I would like to be able to us...
When I put the ESB lib into my BLE Soft Device the MDK tell me that it have some error in it.
What's wrong in my project? if I need ESB+BLE what should I do?(NRF51822+SDK6...
So I installed the Master Control panel software, plugged in the PCA10000, whereupon I was advised to update the firmware in the PCA10000. The firmware update apparently failed...
Hi,
I am trying to get the s130 example to work on my PCA10028 board nRF51.
First I had to change the starting adresse from 0x1C000 to 0x1D000.
I guess that this is due...
There are only the last version nRF51822 Product Specification V3.1 on the web. However, I need a V2.0 PS. So, where can I download the nRF51822 PS V2.0?
Hi,
I wrote a very simple program which compare the analog reference input 0 (P0.00) with AIN0 (P0.26) and generate an interrupt on cross using Low Power comparator on...
Could you update the ble-app-lbs example for SDK 7.1.0?
github.com/.../nrf51-ble-app-lbs
I haven’t been able to get it work.
Since the led_char_add() uses these setters...
Is there a limit to the number of characteristics per (custom) service?
After some testing, it looks like 20 is the maximum (21 causes the device to stop functioning) ...
Hi All,
I am an electronics engineer but new to nRF51822 programming. I have used the PCA10000 & PCA10001 using Nordic SDK, using nRF Studio etc. In nRF Studio, you can...
I'm using SD110, and in my application I have an array of 64, 32-bit integers.
Typically, the client will only need to read 1 of the 64 values, or write to one of the 64...
I'm just getting started with the nRF51-DK, and I'm still confused about which SD I need to load, and which roles I need to support aka GAP and GATT.
My end application...
Hi,
It seems to me that pin assignment and package is the same for both nRF chips. Can I solder nRF51422 chip instead of nRF51822 for ANT testing purposes on my PCA10004...
Hello,
I have a custom board (was built using the Nordic schematics provided with the Smart Beacon Kit). I am using J-Link LITE to try and program the board.
The board...
Today nRF Toolbox App on my Android 5.0 phone is only recognizing HRM code running on my nRF5182-mkit, not other examples.
Today nRFToobox and nRFUART2.0 Apps both...
