Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
After connecting to an nRF9160 using SEGGER tools (J-Link RTT Viewer v7.62b), excess power consumption is observed until the device is reset (via `nrfjprog -r`)
First the...
Hello,
After I upload a new signed image to my device using MCUboot serial recovery (single image), MCUmgr Img_mgmt_client API
img_mgmt_client_state_read() always fails...
Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hello Nordic Team,
For my application, I am using two nRF54L15 chips with one configured as a master and the other a slave. For the remainder of this post, I will be discussing...
Hi, having some issues with the matter door lock sample for the nRF54L15DK on NCS 3.0.2. I'm getting strange failures on boot when running the default matter door lock sample...
Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
Hi, I have a question about Channel Sounding. For my design, I want to use 2 antennas on the initiator and 1 antenna on the reflector. My initiator hardware has an RF switch...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
I used two development boards with 52840, Two development boards are running 'first' and 'second' in the '\examples\802_15_4\wireless_uart\secure', respectively.
Additionally...
Hello,
I'm working with Distance Measurement (nrf_dm) using the NORAB126 module on nRF Connect SDK v2.9.0 and nRF Connect SDK v3.0.1.
I'm facing an issue where, occasionally...
Hi,
We're currently evaluating the cellular capabilities of the nRF91 modem using the nRF9151 DK. We've encountered issues with roaming: when the devkit is taken to another...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
SDK: nRF Connect SDK v3.0.2
DK: nRF54L15-DK
Sample: spi_flash
default:
mspi-max-frequency = < DT_FREQ_M ( 8 )>;
If I change it to 32, it will printf these...
