Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi,
I am trying to write 16bit, 16Khz, 2 channel PCM data to I2S. nRF52840 DK board is connected to speaker via I2S player/decoder board. I am able to hear audio but it...
How can I determine the correct value pull-up resistor to be used on the TWIM port?
The nRF52832 reference documentation mention an internal 13k pull-up however I've always...
I would like to create a program that was a mix of ble_app_multilink_central and peripheral_temperature. The program would work as follows: when the button1 of central is...
I am trying to migrate a blocking SPI transfer code to a non-blocking SPI Manager schedule call. I have 16 transfers queued up in one transaction.
When I launch it, the...
What is the best way to advertise a custom service and allow BLE connections from a mobile device in a Mesh SDK version 2.0.1 application. Previously I had an application...
Initially I had a project in Mesh 1.0. Everything (provisioning, send&receive) was working fine.
Since upgrade to the Mesh 2.1 there is an issue: provisioning still works...
Hi I've found the documentation around BLE_GAP_TX_POWER_ROLES to be a bit sparse. I was wondering if someone could please give me some more info on them
Three roles have...
I am trying to get the thingy52-mesh-provisioning-demo to work with the SDK for mesh 2.1.1 and nRF5_SDK_15.0.0_a53641a.
I am using the Segger Embedded studio project from...
Hi I'm developing DFU project for my application. I need to have both BLE and UART bootloader. If possible, how can I do that?
Many thanks for the answer
Abele - Ital...
Is there any other way for connecting nRF52 DK with our smart phones, other than through NFC?
My smart phone dosen't have NFC feature and I want to run and test the BLE...
On the infocenter website we can read that ,, The nRF5 SDK v15.0.0 supports nRF52 Series devices''. I would like to use crypto code from SDK15 on nRF51. I am interested in...
Hi Nordic
For mesh-sdk-2.1.1, there are two APIs " simple_on_off_client_set " and "simple_on_off_client_set_unreliable" , that can send packet with acknowledge or unacknowledge...
This is my reference to other people's circuit to design
Is this way feasible?
Or is there a document that can be referred to?
I need meanwhile used BLE and 2.4G in...
