RTT log output issue
Hello, I am using SDK v3.0.2 and toolchain v3.0.2. After building and flashing my firmware, no logs are being output to RTT Viewer. What should I do...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Hi all!
I have the NRF54H20 D and somehow the RTT viewer doesn’t work, the board doesn’t work. I am using the most simple zephyr hello world project. It says it is compatible...
Hi there,
We are using for BLE communication a nRF52832 chip with random static address configuration (shown in the UART). Can we be sure that the address of a chip will...
I am building an application for the nRF52840 on Linux just using west . I have been struggling with this issue for some time now. The linker can't find any mbedtls_ccm functions...
Hello, I am experiencing issues with the current measurements taken by the PPK2 when using the nPM2100-EK to power a device. The current drawn from the 2.7V power source ...
I have been trying to get MQTT+TLS to work on the nRF7002 DK and haven't been able to get the samples to connect to the MQTT Broker.
Is there a working MQTT TLS example...
I'm developing on the nrf52840PDK and I was running the cdc_acm exmaple in the SDK to observe the token exchanges between the host and the device.
In the Nordic52840 Product...
Hi all,
I have a module with nRF52832QFAAB0 IC, I'm looking for the IC revision in the compatibility matrix here.
Unfortunately I didn't find any packet variant and build...
I've run the Demo(thingy52-mesh-provisioning-demo). And it works. Now, I want to expand the function.
I 'd like to create more model(for example, sensor model for humanity...
Hi,
Sorry for post here again but i'm having a lot of trumble. I'm actually at the step 4 of the guide, which is the page generation.
I've made correctly all the previus...
I am working on a nrf51822 board and trying to run ble_app_hrs project using nrf sdk 12.1 and s130 softdevice. I converted the uVision project to the Segger Project using...
I use SDK 12.3.0 with IAR
If there is an option to know the last page that programmed?
For example:
Linker: ROM start address 0x1F000 end address 0x76fff
But...
Yesterday, I upload the thingy sdk v2.1.0 in keil uVision5 and rebuild it. After rebuild, it showed one error namely "fatal error" due to the large size(122kb). please suggest...
I am using sdk 14.2.0.I am trying to connect mpu9250 with nrf52832 dev board. whenever I took data serially on putty it is true...but whenever I try to connect it with NRF...
Hi,
I'm new to Segger Embedded Studio developmemt. And now I met a problem similar to Placing data at a specific memory address with Segger Embedded Studio .
I need to...
Hello,
We're creating a program that advertises and reads scan requests RSSI values to determine distance of central device and display them using the onboard leds(1-4)...
We are currently evaluating use of NFC on a nRF52840 which should get powered via VDDH.
Section 7.3 of the data sheet states that NFC can be used in any power configurations...
Hi Nordic engineers,
I found a strange problem that NRF52840 voltage of io high level is just about 2.65v~2.71v. I am sure that the voltage mode is normal voltage mode...
Hello,
I'm attempting to solve some issues with my BMD-200 (nrf51822) not getting the SD BLE_GAP_EVT_DISCONNECTED message. I currently Don't seem to be getting this message...
Hi, I'm not able to find the memory layout of the nRF52840 without the SoftDevice. I'm working with the nRF52840-Preview-DK and the SDK v15.0.0. I don't need the SoftDevice...
Hi sir,
we use nRF 52832 with ESB protocol. and we use ACK to send payload to PTX , but we found must use the same pipe which PTX used pipe to send ACK .
so , I have two...
