RTT log output issue
Hello, I am using SDK v3.0.2 and toolchain v3.0.2. After building and flashing my firmware, no logs are being output to RTT Viewer. What should I do...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Hi all!
I have the NRF54H20 D and somehow the RTT viewer doesn’t work, the board doesn’t work. I am using the most simple zephyr hello world project. It says it is compatible...
Hi there,
We are using for BLE communication a nRF52832 chip with random static address configuration (shown in the UART). Can we be sure that the address of a chip will...
I am building an application for the nRF52840 on Linux just using west . I have been struggling with this issue for some time now. The linker can't find any mbedtls_ccm functions...
Hello, I am experiencing issues with the current measurements taken by the PPK2 when using the nPM2100-EK to power a device. The current drawn from the 2.7V power source ...
I have been trying to get MQTT+TLS to work on the nRF7002 DK and haven't been able to get the samples to connect to the MQTT Broker.
Is there a working MQTT TLS example...
Hi All,
I would like the nrf51822 sleep, wake up and then continues advertising.
I try following code:
NVIC_DisableIRQ(RTC1_IRQn);
NRF_RTC1->EVTENCLR...
hello, everyone.
i am a new, i can't understand the meaning of "One event can trigger multiple tasks by using multiple channels and one task can be triggered by multiple...
Please provide me some details about how to implement watchdog functionality so that i can reset the entire system for avoiding software Hangs
I have come up with a code...
Hi,
I have downloaded the SDK 6.0 which contains the ble_app_uart and tried to compile it using GCC, but getting the following error which doesn't make any sense because...
I see the nrf51822-DK and and nrf51822-EK are now marked 'not recommended'. Why is this?
I now see an nRF51-DK and an nRF51 dongle. Are these now the current development...
Hello,
I want to use broadcaster mode for nrf51822, could you tell me please what I must to do to use this mode?
I suppose I must to set BLE_GAP_ADV_TYPE_ADV_NONCONN_IND...
Hi,
We need to develop piconet where each device able initiate receiving and transmitting data.
According to a Bluetooth Core V4.0 specification this topology named like...
Hi Nordic DEV Team,
In my application, I would like to use sd_flash_page_erase to erase like 100 pages user data; the problem of pstorage is that I cannot specify the page...
I am connecting my development device acting as a BLE keyboard using HID over GATT and it seems to be draining the phone battery very quickly. Every 7 seconds I would get...
I am using a US-100 ULTRASONIC SENSOR MODULE, and I need to measure the pulse width that this sensor produce. In arduino we can use a metode called "pulseIn", that gives you...
Hello-
I'm trying to load the Blinky example, I am using the nRF51822 Evaluation board.
I am able to compile but cannot load the board, a window with "Cannot Load Flash...
I use the Timer2 and the PPI for toggle a GPIO to control the frequency of 16Mhz Quartz is correct.
But when I stop the function I have a permanent consumption of ~ 6 mA...
As title.
I want to make a ANCS function on serialization codecs. But I think that is not support on original serialization source code.
How can I make a ANCS function...
Hello all,
we want to design a new product. in short description, it can be view as a key fob dongle and an access reader.
the key fob can be a stand alone key fob ( as...
