I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
szenario
beacon and receiving nodes are all MCU based and all powered by net, no local battery needed
the beacon usually located near the floor, the nodes will be located...
Blicky project runs and I can set break points and run through them - watching the LEDs blink appropriately. However, the HRS and Proximity projects will successfully load...
Hi all,
I'm using the LE1 to do the mutilceiver,if I donn't use the dynamic payload,I can do it successfully.However,if I use the dynamic payload to do Multiceiver,the...
Hi,
For the LE1,I found that 32.768kHz crystal oscillator need long time(about 350ms) to running,I must do some delay(about 350ms) for the software then use the RTC,or...
In moving to the "rev-2 51422 silicon, we find that the app_timer inevitably fails after minutes to several hours. Power requirement moves from about .002ma to 4.5ma then...
Hi,
I am planning to use an external DCDC to supply the NRF51822 in Low Voltage Mode.
In the datasheet a voltage range of 1.75-1.95 on VDD and VDD1.8 is mentioned. ...
Dear all
I'm testing for RF stability. As i used 24LU1(host) with 51822(device) be the platform. For audio data transmission. 8k 8bits data rate.
Timeslot set as 1008us...
Hi,
I don't have any problems running the bootloader with S110 7.0.0.-3.alpha on the PCA1001 but when using the same code (minus the led and button config of the PCA1001...
Hi,
I am having a hard time with the permanent storage.
I got it to work with updating a 24 bytes long struct in a persistant block of 32 bytes.
I noticed that the...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hello Gentlemen,
I'm looking for a good example on how to pair BLE sensor and Android using static passkey. I looked at ble_app_gls but I could not see how they set the...
I have the following code
// bondmngr code comes here for now
ble_bondmngr_init_t bondInitData;
bondInitData.flash_page_num_bond = FLASH_PAGE_BOND;
bondInitData.flash_page_num_sys_attr...
I want to save data sent by the Nordic UART/Serial Port Emulation over BLE to the phone.
Can the Nordic UART app save received UART data sent over BLE to the phone?
I've tried adding in the examples (heart rate by example) the:
sd_app_evt_wait();
(including #include "nrf_soc.h" and #include "nrf_sdm.h")
Disabling led, etc. And...
I am running into some symptoms here that I'm not understanding.
My peripheral is an nRF51822 using the S110 softdevice. It implements a service which sends out notifications...
