Hi,
I want to add scheduler server to the mesh/light sample with nrf52DK, I change the element define like below:
static struct bt_mesh_elem elements [] = {
BT_MESH_ELEM...
Hi,
I’m working with an nRF52832 DK board that’s stuck in bootloader mode—LED 5 just keeps blinking. Here’s what we’ve tried so far:
Held the IF BOOT/RESET button...
Hello,
After I upload a new signed image to my device using MCUboot serial recovery (single image), MCUmgr Img_mgmt_client API
img_mgmt_client_state_read() always fails...
Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hi,
Can't get rid of compilation error about undefined NRFX_SPI0_INST_IDX after adding nrfx_spi driver. Searched the forums and found similar issues but none of the suggested...
Sir,
Did you succesfully compile the NRF5 mesh on SEGGER STUDIO ? I did try with updated segger but i am getting the same error!
And i cant see too the sdk_config.h to...
Hi,
I just received nRF52-DK recently.
I am using Ubuntu 16.04 (64-bits) OS.
I installed JLink_Linux_V620b_x86_64.deb and was using nRF5x-Command-Line-Tools_9_6_0_Linux...
Hi, I am developing an SPIS interface on the nRF51822 using SDK v12.3.
I have configured my device for EasyDMA and I expected to see a continuous stream of data being transmitted...
Hi.
I applied https://github.com/crfosse/Thingy-52-to-nRF52xx project to get thing'y motion sensor by nRF52840 DK.
When I init DK, it discovered only 7 UUID so euler,...
Hi Everyone
I am trying to use BME which is an i2c/twi sensor and EPaper which is an SPI based module. In my code i am using TWI INSTANCE ID 0 AND SPI INSTANCE ID 0.
I...
Hi all:
I am developing the driver of ST LIS3DH and its mcu is NRF52.
If I want to read the value of whoami.
I am not sure if I need call the function of
nrf_drv_twi_tx...
Hi everyone. I'm starting from scratch and using as reference the example/ble_peripheral/ble_app_template.
I'm using Embedded Studio 3.50 + Jlink V6.32 / The chip is nRF52832...
Hi,
I am running the BLE app uart example, using Segger Embedded Studio in Windows.
I've found that that after build and run procedure, the firmware doesn't run, as there...
I am using Master Control Panel 3.10.0.14 with 2 nRF51 Dongles. I can select a dongle and perform a Start Discovery and see devices. Next, I install Microsoft Universal Windows...
Hi
I'm facing a problem since I've upgraded to SD140 6.1 .
I'm running as multilink central, and want to keep scanning even after connection. I scan with the following...
Hi,
I am working on an application using the nrf52 sdk v15 and nrf Mesh sdk v2.1.1 on nrf52840 PDK. Starting from the nrf5_SDK_for_Mesh_v2.1.1_src\examples\sdk_coexist\ble_app_uart_coexist...
I'm currently adding a large characteristic (5.3 times bigger than my max MTU) to my device that supports multiple peripheral connections. This characteristic is used to set...
