Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
I have a nrf9160 DK but when upload SLM application to it i can not send AT commands to it over it's usb port but in asset tracker application it works i want to modify SLM...
Finally we got our prototype boards and proof of concept firmware code done and we are a bit stuck on the average power consumption over time for the entire sensor that is...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
Hi,
I have integrated Neuton’s “Transport Type Detection” pre-trained model into my firmware, running on a nRF52840dk. For collecting 9-axis IMU data, I’m using the ST X...
Hello Nordic Team
I am using SDK 3.0.1 with a nRF52DK to develop a firmware that can be switched from BLE mode to GAZELL mode and vice versa over a command sent via UART...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi All,
I am using Keil and GCC but I want to migrate my projject to "Seggers Embedded Studio for ARM". After following the tutorial about migration, i have been able to...
I've been doing some exercises with the FDS module to ensure I understand it and have come across an issue. When I write I am not seeing a write call-back in the fds_event_handler...
I do not know why the comparator does not compare correctly. I use AIN6 as Vin+; ANI0 as Vin-. The code is show in below. The comparator is work in differential mode.
...
Hello,
I am using the following
Mesh Version : nrf5_SDK_for_Mesh_v2.2.0_src
SDK Version : nRF5_SDK_15.0.0_a53641a
IDE : SEGGER Embedded Studio for ARM Release 4.10...
Just wondering if anyone knows a reliable method to update a project to use a new SOFTDEVICE version?
One that can be repeated for each new release.
I am using Segger...
Hi,
I have a question about pairing a phone with the nrf52832.
During the pairing phase (the phone see our device that is advertising and then starts the paring procedure...
Hello,
i am facing issue with nRF5x Command Line Tools. I am using custom board with nRF52832. While i am using Segger J-flash Lite there is no problem to flash program...
I am developing a wearable using nRF52832 and looking for best debugging practice. I have given provision for SWD pin connection on PCB board. What is the best suitable JLink...
Dear all,
I'm looking if there is a easy way to add custom commands to the OpenThread CLI without touching the OpenThread core ? I didn't find anything in the API.
Thank...
Hi Nordic team,
I having problem understand TWI_INSTANCE_ID and what are usage of this configuration?
For example, if I were to use 2 different TWI hw port (SCL1,SDA1...
I am using a raspberry pi that is running a NUS service. The PacketList in Wireshark shows the advertising packets from the device, but the device is not showing up in the...
Hello, in sdk 15.2 there is an SES version of radio_test for pca10040, and within main.c, starting on line 121, there is reference to NRF52810_XXAA. Is this to understand...
Hello,
I am developing an application in which mesh client in some cases needs to send consecutive messages to the mesh server. I use a modified version of Simple On/Off...
Hi,
I am trying to modify the enocean switch example to send the commands from the switch to different devices connected in the mesh. Example shows that the a0, a1 control...
