Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
As far as I understand from this page [https://openthread.io/platforms Host / 802.15.4 Controller section] it is possible to have Dongle running thread attached to PC...
Hi, everyone,
We develope project on nRF52832 Chip. It has one UART port and we need to make it working as RS485. For this purpose we connected to TX/RX pins the required...
I am trying to send hundreds bytes to peripheral, the best tool that I can find, is still nrfConnec. But the data only be typed one by one. Is there any way let it load a...
I am using a nrf52832 with SDK 15.2 and softdevice s132 v6.1
My peripharal should transmit an iBeacon to wake up an application on the smartphone and also transmit a connectable...
Hello,
For a new project I am using the Decawave module DWM1001. This module is equipped with an NRF52832. I have already used the nrf52832 for previous project and I face...
Hi there,
Is there a specific sequence needed to power-up the NRF52840?
Let me get into the details:
My design uses configuration #5 from the datasheet (see below...
Hi, I'm using the serial example from the nRF5 SDK for Mesh (version 2.2.0) and after running it for extended time with data being received from nodes every few seconds, it...
I have a small app_usbd demo which works fine on the nrf52 dongle, but not on the larger nrf52840-dk.
I am running SDK 15.0 with the errata fix mentioned on several other...
ATT MTU THROUGHTPUT EXAMPLE FOR nRF52810 on KEIL using S132 v5.1.0 PLEASE >>>>>>>>>>>>>
Tried this : https://devzone.nordicsemi.com/b/blog/posts/the-s132-v5-1-0-is-now...
Hi!
I am currently developing product containing Thread mesh and BLE peripheral service. I am using Thread SDK v2 in my software. My application has to support writing to...
Is there any NRF51822 DFU guide under following conditions:
a. NRF51822
b. SDK11.0.0
c. Dual Bank BLE DFU(\examples\dfu\bootloader\pca10028\dual_bank_ble_s130\)
I...
Hello i am working with light switch proxy client server sdk example.i make provision light and switch using nrf mesh application.i have three nrf52832 dk board.i flashed...
Hi.
I work with PCA10040 and SKD_14.2.
I use UARTE with easy DMA. I see big enough delay between sending nrf_drv_uart_rx_abort and entering to UART event hanler. What...
