Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
I've set up a timer which is firing the interrupt correctly. I then set up a second compare and linked it to the PPI to fire the ADC. The idea is to do these a few times per...
Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
Greetings!
I am using nRF52832 with SDK 16.0.0 and mesh sdk 4.0.0.
Application: light switch client with LPN features added
In one of application, I have to use...
i already done the nrf52840 dongle that already work as beacon when i have tried in nrf beacon apps. i want the same application but now it is transmitting to server/website...
Hi,
I have a low level mcu (128 kbyte flash) connected via UART to the nRF52840.
My current flash usage (text output arm_gcc) is about 256 kbyte + the softdevice.
Since...
I am somewhat of a beginner - I have successfully built and programmed a "Hello World" example on the nRF5340. However I am having trouble building some of the Bluetooth samples...
So I am using the Mesh SDK in version 4.0.0 and 2 nrf52DK boards with some custom software running on the boards, but derived from the light switch examples. The boards work...
We have some prototype boards that work fine when programmed via the debug out on the nRF52 dev kit, but have problems when programmed with this JLink . Programming with both...
Hi Team,
We are using the NRF52832 Board for our development purpose.We need the last RESET condition reason/source and need to store as log in memory for further debugging...
Hello,
I am looking for some tips to speed up a DFU transfer.
I have 2 BLE, I implemented a DFU master in the first one using SDK11.
Transfer duration is about 3mn30s...
Hi, I am trying to do firmware upgrade of nRF91 over BLE using nRF52 on the nRF91-DK or Thingy91 board. They both have nRF91 and nRF52840 chips on them which are connected...
I am currently working on a Heart rate sensor(max30102). I have connected the sensor to my nrf52 DK as follows: GND -> GND VDD -> VIN SCL -> P0.27 SDA -> P0.26 INT -> P0.17...
Hi everyone,
I have lately had some problems with my application which has different characteristics enabled, such as nus, battery service, dfu etc...
The problem I am...
Hi team,
I have 2 Thingy:91s, 1 is maybe new, not sure if I have used it before and 2 has been used before and reprogrammed over SWD many times before.
I wanted to test...
