Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
After checking and searching, i found this ble_gatts_conn_cfg_t::hvn_tx_queue_size should be the key to set it. In my custom project (SD132 V5 + SDK14.1) the only setting...
Hi
I'm using IAR Compiler and need to generate some PWM outputs. I tried to use the example code from the pwm_library. But the compiler is generating an Error on the macro...
I am using PCA 10040 development boards with soft device version s132_nrf52_3.0.0 to investigate Central/Peripheral communications.
A PCA 10040 acts as a Central making...
Here is calibration of UART data using ADXL345.
and the data is followed by x, y & z value, for example x = -42, y = 20, z = 268. and then after calibrated 10x which is...
We are upgrading an existing product to use Bluetooth instead of the parallel port.
It must support >20kbit/sec communications between the device and the host PC.
We...
Hey Nordic devzone,
I am tinkering with the following multiprotocol examples:
ble_thread_dyn_mtd_coap_cli (client)
ble_thread_dyn_template (server)
Currently the client...
Hi, I'm using nRF52832 with sdk 13.1.0(softdevice 4.0.2). I had trouble to connect nRF52832 in some android smart device.When I restart Bluetooth,Sometimes there are problems...
Hi, I'm using nRF52832 with sdk 13.1.0(softdevice 4.0.2). I had trouble to scan nRF52832 in android smart device.When i disconnect the device a long time when the status is...
hello,
I use my own code to test IOS message notifications ,
call nrf_ble_ancs_c_request_attrs function， then did not receive the data source,
Triggered the BLE_ANCS_C_EVT_NP_ERROR...
I am following blogs and questions for image transfer with nrf52 and arducam on this site and github . I can see we can use arducam OV2640 module. It has FPGA chip at back...
Hi all , I have a trouble . I am using ble_app_hrs_rscs_relay example . I modify it for NUS service . I have 3 board . peripheral <-> role <-> central via NUS . It work fine...
Im following the example Alert Notification Application and read this instruction:
In nRF Connect, create the Alert Notification Service (ANS) server by performing the...
Based on my experiment, ATT_MTU sample application can achieve throughput of 900 Kbps with the following settings:
SDK 14.2.0
ATT MTU size: 247
Connection interval...
I have a Nordic nRF52-DK that I am using to create and run programs written using the mbed compiler. I have followed the instructions outlined here on the mbed website( os...
