Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
Hi.
I wonder if you could help me:
I'm using a thingy91x and would like to work with the npm1300. In the case of this hardware, the PMIC npm1300's i2c bus is connected...
RTT log output issue
Hello, I am using SDK v3.0.2 and toolchain v3.0.2. After building and flashing my firmware, no logs are being output to RTT Viewer. What should I do...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Hi all!
I have the NRF54H20 D and somehow the RTT viewer doesn’t work, the board doesn’t work. I am using the most simple zephyr hello world project. It says it is compatible...
I'm developing a minimal bootloader on the nrf52832 that just reads/writes flash and decrypts some data already present in flash. I'm using the Bluetooth Spec's own sample...
nRF51822 sdk9.0
I am having a problem with GPIOTE. I have four interrupts programmed on four different pins.
As long as the signals do not transition at the same time...
I would like to use an external JLink and the interface MCU's virtual COM at the same time. I want to control the nRF52840 via UART connection using one host (Raspberry Pi...
Hi. I have a peripheral application that spends a lot of time doing stuff, but not in a BLE connection. In order to debug it, I have it use nrf_log with a backend that just...
Hello,
I would like to capture sound using pdm driver and to get this info in the computer using uart.
When I have the buffer from pdm I copy some data in a buffer to...
Hi,
I was looking to buy passive components for NRF51822 QFAA. Bill of Materials states specific tolerance and dielectric which is very difficult to find so, can anyone suggest...
Hi,
I try sample code usbd with PCA 10056 and it work.
On my custom board, same sample work fine too. But when I plug jtag, and try to debug my code, usbd can't be enabled...
ble_senso4s_v_0_7_poenostavljena4_1 power_manager.rar Hi
I read a lot about p_storage library and I tested it and works great if I use SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM...
Hi,
when using the following codes, I have some errors related with the ID of record,
please help to let me know the solution,
The errors are NRF_ERROR_INVALID_PARAM...
My application runs on nRF52832 with SDK11.
what happens if I call nrf_drv_spi_transfer in blocking mode from different contexts on the same SPI instance.
in my case the...
Hello,
I have a device that need ANT and BLE (central and peripheral) comunications. I found some examples about Ble central and peripheral but they working on s130 soft...
I am porting my code from SDK 13 to SDK 14.2 (nRF5_SDK_14.2.0_17b948a) and following the
migration guide . In the SoftDevice handler section I think the following section...
We are using LG Nexus 5 (Android v 6.0.1) and nRF52840 PDK. Currently when IO capabilities on nRF52840PDK are configured to Keyboard and Display, the numeric comparison is...
I would like to have ble_app_uart + usbd_msc. Now the problem is that SD not suporrt the USB power events,as a result, I can not check when usb is plug in and request USBD...
Hi,
I am using nrf51822 pca10004 with SDK110 v8 , I got a problem that the code hangs in sd_softdevice_enable and stuck in SVC_Handler.
Thanks,
Nagaraj
