Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
RTT log output issue
Hello, I am using SDK v3.0.2 and toolchain v3.0.2. After building and flashing my firmware, no logs are being output to RTT Viewer. What should I do...
Hello All,
I am working on NFC using nRF52832 chipset .
I followed the below this link for http://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5...
Hi everyone :D
I'm not being able to compile a c++ code on segger embedded studio.
The same code compiles with the Makefile provided in the SDK 14.2, but not with the...
Hey, we are using the nrf52840, and the SDK 14.0.2 and the uart example. We need to set the BLE range to max, and therefor the TX to 8db, the transfer speed to 125kb/s. We...
This is my second attempt at merging a pure UART App (no soft device) into an App derived from the ble_app_template (with soft device)
I see I am not alone in having suffered...
Hello everyone, I would like to make an unconnected broadcaster to send data to the advertising channels ... I come from a X-NUCLEO-IDB05A1 board and that's has been pretty...
Hi
in the release notes of the SDK14.2 the following is written
The following toolchains/devices have been used for testing and
verification:
- ARM: MDK-ARM version 5...
I have written an interrupt program to blink an led at port P1.01 by pressing the button 1.So i added the code in ble_app_blinky example so i can blink the led from the board...
I want to read integer data on the cloud
for example int a=1001;
This value must be displayed on the cloud service after every 5 seconds.Also i want to increament the value...
I urgently need to decide on the use of the chip in future developments and deliveries. There was no problem with the 51822 chip in the connection between 51822 to BlueGiga...
We are working on an IoT application using the nrf52840 Preview DK and would like to interface an external Wifi Module for transfering the acquired data to the internet. Could...
I am using SDK 14.0.0 with Softdevice S132 V5.0.0 and the accompanied DFU libraries. In the examples\dfu\bootloader_secure_ble example I think the logging system has a problem...
Hello,
When I try to read data from UART RX port using serial library, I'm not able to read the data beyond the number specified by
SERIAL_FIFO_TX_SIZE and SERIAL_FIFO_TX_SIZE...
Hey, I'm using raspberry pi 3 model b, with the rasbian strech os running in it. I have followed the tutorial provided by nordic using this link for BLE over IPv6. When I...
Hello, In my case, i'm using some PTX and one PRX. It's working well. Now i want to extend coverage, can i use repeater/forwarder? I tried but have problem with PTX: after...
